Abstract:Statement of problem: Strength-gradient zirconia combining 3 zirconia formulations with different flexural strengths has been reported to have outstanding mechanical properties. However, data concerning the effect of different sintering protocols on the fracture strength of 3-unit monolithic gradient zirconia fixed partial dentures (FPDs) are sparse. Purpose: The purpose of this in vitro study was to test the effect of different sintering protocols on the fracture strength of 3-unit monolithic gradient zirconia FPDs. Material and methods: Two custom-made stainless-steel master dies were designed to replicate a mandibular right second premolar and second molar prepared to receive a 3-unit monolithic zirconia FPD. Thirty monolithic zirconia FPDs were milled from gradient zirconia blanks and allocated to 3 groups (n=10) according to the sintering protocols: high-speed sintering, speed sintering, and conventional sintering. The FPDs were cemented onto the corresponding dies with traditional glass ionomer cement. All FPDs were cyclic loaded (600 000 cycles/49 N/1.7 Hz) in a mastication simulator. Fracture load measurements for each FPD were determined by using a universal testing machine. Scanning electron microscopy (SEM) at ×80 magnification was used to examine a fractured FPD from each group. A representative specimen from each group was examined with SEM at ×30 000 magnification to determine the grain size. One-way ANOVA, pair-wise Tukey honestly significant difference (HSD), and Pearson correlation tests were used for statistical analysis of the data (α=.05). Results: The high-speed sintered FPDs recorded the highest statistically significant fracture load mean ±standard deviation value (2526 ±300 N), followed by the speed sintered FPDs (2136 ±127 N), while the lowest statistically significant fracture load mean value was recorded with the conventionally sintered FPDs (1361 ±181 N) (P<.001). In addition, the mean ±standard deviation grain size values were 488 ±272 nm for the high-speed sintered specimen, 578 ±409 nm for the speed sintered specimen, and 832 ±551 nm for the conventionally sintered specimen (P<.001). A significant negative correlation was found between fracture strength and grain size among the 3 groups. Conclusions: The fracture strength of 3-unit monolithic gradient zirconia FPDs sintered by using a high-speed protocol was significantly higher than that of speed and conventionally sintered FPDs (P<.001). The high-speed sintering protocol reduced the mean grain size of gradient zirconia FPDs compared with that of both speed and conventional sintering protocols.

[Effect of Two-Step Sintering Method on Properties of Zirconia Ceramic].

Effect of Chairside Rapid Sintering Process on Microstructure and Mechanical Properties of TZP Zirconia Ceramics

The effect of zirconia sintering temperature on flexural strength, grain size, and contrast ratio

Impact of the sintering parameters on the grain size, crystal phases, translucency, biaxial flexural strength, and fracture load of zirconia materials

Effect of high-speed sintering on the microstructure, mechanical properties and ageing resistance of stereolithographic additive-manufactured zirconia

Effect Of Sintering Temperature On Structures And Properties Of High Quality Zirconia Ceramics Under Oscillatory Pressure

Effect of sintering programs and surface treatments on monolithic zirconia

Effect of dosing frequency on bisphosphonate medication adherence in a large longitudinal cohort of women.

Effect of sintering procedures on optical properties, chemical composition, and grain size of monolithic zirconia ceramic at different thicknesses after hydrothermal aging: An in vitro study

Mechanical Performance of Polymer-Infiltrated Zirconia Ceramics.

Effects of sintering temperature on properties of diatomite-based dental ceramic

Effect of Multistep Processing Technique on the Formation of Micro-Defects and Residual Stresses in Zirconia Dental Restorations.

Effect of different sintering protocols on the fracture strength of 3-unit monolithic gradient zirconia fixed partial dentures: An in vitro study

The effect of adhesive surface with porcelain sintering and two silane coupling agents on the adhesive properties of zirconia

Effects of Ceramic Density and Sintering Temperature on the Mechanical Properties of a Novel Polymer-Infiltrated Ceramic-Network Zirconia Dental Restorative (Filling) Material

Effect of final temperature and heating rate on the mechanical and optical properties of a zirconia veneering ceramic

Methods to improve mechanical characteristics of ceramics on the basis of zirconium and hafnium diborides (Review)

Preparation of Zirconia Ceramics by Spark Plasma Sintering Technique and Their Mechanical Properties

Effect of coloring and sintering on the translucency and biaxial strength of monolithic zirconia

Effect of Sintering Temperature on Compressive Strength of Porous Yttria-Stabilized Zirconia Ceramics

[Study of relationship between powder-size gradation and mechanical properties of Zirconia toughened glass infiltrated nanometer-ceramic composite powder]