Abstract:The analog-to-digital converter (ADC) is a key building block of today's high-volume systems-on-a-chip (SoCs). Built-in-self-test (BIST) is the most promising solution to testing deeply-embedded ADCs. Cost-effective stimulus source with on-chip integrability has been viewed as the bottleneck of ADC BIST, and consequentially the bottleneck of SoC BIST and BIST-based self-calibration. The deterministic dynamic element matching (DDEM) technique has been proposed as a solution to this problem. In this work, rigorous theoretical analysis is presented to show the performance of a DDEM digital-to-analog converter (DAC) as an ADC linearity test stimulus source. Guided by the insight obtained this analysis, a systematic approach for cost-effective DDEM DAC design is proposed. Two generations of DDEM DACs have been designed, fabricated, and measured. 12-bit equivalent linearity was achieved from the first DDEM DAC with 8-bit apparent resolution and less than 5-bit raw linearity after systematic error compensation. The achieved 12-bit linearity outperforms any on-chip stimulus source in literature. Based on the first design, a new DDEM DAC with 12-bit apparent resolution, 10-bit raw linearity, and 9-bit DDEM switching was designed with improved design technique. This DAC was fabricated in standard 0.5-pm CMOS technology with a core die area of 2 mm2. Clear ramp signals could be observed on an oscilloscope when the DDEM DAC was clocked at 100 MHz. Laboratory testing results confirmed that the new DDEM DAC achieved at least a 16-bit equivalent linearity; this was limited by the available instrumentation, which has 18-bit linearity. It outperforms any previously reported on-chip stimulus source in terms of ADC BIST performance by 5 bits. The robust performance, low cost, and short design cycle for on-chip implementation make DDEM an enabling technology for SoC BIST and self-calibration. Two new approaches based on DDEM are developed to further boost the die area efficiency, improving the basic DDEM approach. The first is termed segmented DDEM, and the second is dither-incorporated DDEM (DiDDEM). It has been shown through mathematical analysis and simulation that these can maintain the performance of the basic DDEM approach while greatly reducing the implementation cost.

Dither Incorporated Deterministic Dynamic Element Matching For High Resolution Adc Test Using Extremely Low Resolution Dacs

Testing High Resolution Adcs With Low Resolution/Accuracy Deterministic Dynamic Element Matched Dacs

Parameter Optimization Of Deterministic Dynamic Element Matching Dacs For Accurate And Cost-Effective Adc Testing

Testing high resolution ADCs using deterministic dynamic element matching

A deterministic dynamic element matching approach for testing high-resolution ADCs with low-accuracy excitations

Deterministic dynamic element matching: an enabling technology for soc built-in-self-test

Modeling of digital background calibration with signal-dependent dithering for a 14-bit, 100-MS/s pipelined ADC

A 12-BIT 400-Ms/s CURRENT-STEERING DAC WITH DEGLITCHING TECHNIQUE

Deterministic DEM DAC Performance Analysis

Dynamic Element Matching with Signal-Independent Element Transition Rates for Multibit $\delta\sigma$ Modulators

A Novel Dynamic Element Matching Technique In Current-Steering Dac

A Parasitic Elimination Bootstrapped Switch and a Fast Settling Residual Amplifier for High-Speed and High-Resolution Pipelined ADC

A 14-Bit 1.0-Gs/S Dynamic Element Matching Dac With > 80 Db Sfdr Up To The Nyquist

An 18-Bit High Performance Audio Sigma-Delta D/A Converter

A Novel Dynamic Element Match Technique in Current-Steering DAC

A random DEM technique with minimal element transition rate for high-speed DACs

Understanding High-Resolution Dynamic Element Matching DACs

An 18-Bit High Performance Audio ∑-△D/A Converter

A Fully Dynamic 4-Channel 13b Simultaneous Sampling Incremental ΔΣ ADC Using Cascoded Floating-Inverter-Amplifier and Code Division Multiplexing Technique

Thermo Data-Weighted Average Dynamic Element Matching (Dem) Encoder For Current-Steering Dacs

Binary tree structure random Dynamic Element Matching technique in current-steering DACs