Abstract:A Cu-0.41Mg-0.06Ca (wt.%) alloy was processed by equal channel angular pressing (ECAP) for up to 12 passes via Bc route at room temperature, and its homogeneity was evaluated from three aspects of hardness, microstructure and crystallographic texture. The hardness was measured in detail on the whole transverse planes, and the microstructure and the crystallographic texture in the central and bottom regions on the transverse planes were investigated by electron backscatter diffraction (EBSD) technique. After 1 ECAP pass, the hardness in the central region was 9.4% higher than that in the bottom region; the microstructure in the central region consisted of the elongated grains, while that in the bottom region was composed of the slightly distorted grains; the crystallographic texture in the central region followed the ideal orientations of the ECAP crystallographic texture, nevertheless the crystallographic texture in the bottom region obviously deviated from any ideal orientation of the ECAP crystallographic texture. Then, with the increase of ECAP passes, the hardness and microstructure differences between in the two regions gradually weakened, and the deviation of the crystallographic texture in the bottom region gradually decreased. After 8 ECAP passes, the both regions showed the same hardness, the similar ultrafine-grained microstructure and the similar crystallographic texture. The difference formation should be attributed to the non-uniform strain caused by the friction between the sample and the die wall, rather than caused by the corner gap. The difference weakening should be attributed to the strain hardening behavior of metals. The strength calculation showed that the Cu-Mg-Ca alloy after 8 ECAP passes had almost the same yield strengths where 593 MPa for the central region and 583 MPa for the bottom region, showing only 1.7% difference.

Intermediate annealing of pure aluminum during cyclic equal channel angular pressings

Annealing Behavior of Aluminium Deformed by Equal Channel Angular Pressing

EBSP Study of the Annealing Behavior of Aluminum Deformed by Equal Channel Angular Processing

Microstructure and mechanical properties of AlMgSi alloys after equal channel angular pressing at room temperature

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Intermediate Annealing of Pure Copper During Cyclic Equal Channel Angular Pressing

Effects of Annealing Treatment on Mechanical and Tribological Performance of Cu–10Al–4Fe after Equal Channel Angular Extrusion

Mechanical and microstructural characteristics of AA6082 using thermal equal channel angular pressing for structural applications

Microstructure and mechanical properties after annealing of equal-channel angular pressed interstitial-free steel

Microstructure Evolution in High Purity Aluminum Single Crystal Processed by Equal Channel Angular Pressing (ECAP)

Grain Refinement and Strengthening of an Aluminum Alloy Subjected to Severe Plastic Deformation through Equal-Channel Angular Pressing

Conjoint influence of equal channel angular pressing and annealing on microstructure and mechanical properties of aluminum alloy 7075Gemeinsamer Einfluss des Gleichkanal‐Winkelpressens und des Glühens auf das Gefüge und die mechanischen Eigenschaften der Aluminiumlegierung EN AW‐AlZn5,5MgCu

Microstructure and Properties of Ultrafine-Grained Aluminum-Based Alloy Processed by Equal Channel Angular Pressing

Microstructure and Texture Change in Equal Channel Angular Pressed 6061 Aluminum Sheet by Static Annealing

Ebsp Investigation of Microstructure and Texture Evolution During Equal Channel Angular Pressing of Aluminium

Direct Observation of Shear Deformation During Equal Channel Angular Pressing of Pure Aluminum

Influence of Equal Channel Angular Pressing and Cyclic Extrusion Compression on the Microstructure Evolution and Mechanical Properties of Pure Aluminum

Structural Coarsening During Annealing of an Aluminum Plate Heavily Deformed Using ECAE

Annealing Effect of High-Density Pulsed Electric Current Treatment on Cold-Rolled 6061 Aluminum Alloy

Effects Of Ecap And Annealing Treatment On The Microstructure And Mechanical Properties Of Mg-1y (Wt. %) Binary Alloy

Investigating the Influence of Thermomechanical Equal Channel Angular Pressing (ECAP) Improved Die on AA-6061