Abstract:High-reflectance ohmic contacts to p-GaN are the key for Flip-chip ultra-violet light emitting diode (UV-LED) to improve the external quantum efficiency (EQE), so the kinds of metal or alloy film both ohmic contact and the reflector of light are important to choose the appropriate high-reflectance and low-resistance ohmic contact to p-type GaN. The GaN-based LED samples used were grown by Metalorganic Chemical Vapor Deposition (MOCVD). Four different metal films were deposited on the surfaces of p-GaN and annealed Ni/Au alloy. The thickness of these metal films varied from 30 nm to 840 nm. The reflectance and transmittance of the samples were mea- sured by WGS-9 system. The 2θ scans XRD and surface AFM images of the samples were also observed. As results, when the films' thickness under the 130 nm the reflectance of Ag-deposited samples increased with the increasing thickness and the transmittance decreased at wavelength of 400 nm. The reason of the increasing of reflectance is the reduction of the light transmitted through the films. When the films' thickness over 130 nm, the reflectance of Ag-deposited samples decreasing. From the results of XRD and AFM, the metal film formed multi-layers film and the roughness R_a and R_q increased with the increasing thickness. It is suggested that the diffusion of the multi-layers films is the main reason of reduction of reflectance with the films thickness increasing. Other metal films show the same characteristics as the Ag-deposited films. From the result of reflectance, Al and Ag are the suitable candidates for the reflector, but it is reported that the single Al or Ag films don't make good ohmic contacts on p-GaN. So a thin annealed Ni/Au is adopted to interspersed between the Al or Ag reflector and the p-GaN in order to provide efficient hole injection into the device. From the results of reflectance and I-V curves of Ni/Au/Ag and Ni/Au/Al, the I-V characteristics of Ni/Au/Ag and Ni/Au/Al contacts are similar to this of Ni/Au annealed. However the reflectance of Ni/Au/Ag and Ni/Au/Al contacts is three times higher than that of Ni/Au at wavelength of 400 nm. These results demonstrated that Ni/Au/Ag and Ni/Au/Al can be used as high-reflectance and low-resistance p-GaN ohmic contacts for flip-chip UV-LEDs

Analysis of Optical and Electrical Properties of Ag/ITO Composite Membrane for GaN-based LED

GaInN Light-Emitting Diodes with Omni-Directional Reflector Using Nanoporous SnO2 Film

Optical and Electrical Properties of the LED Using ZnO:Ga Film As Current Diffusion Layer by Sol-gel Technique

Highly Reflective Ni/Ag/Pt/Au Ohmic Contacts To P-Gan With Ito Interlayer

Effect of ITO Interface Modulation Layer on the Performances of LEDs with Ga-doped ZnO Electrode

Simulation of Nanoscale ITO Top Grating of GaN LED

The Effect of the Original Thickness of Ag in the Graphene–Ag Nanodots Transparent Conductive Layer on the Electrical and Optical Properties of GaN-Based UV-LEDs

Ohmic Contact of High Reflectivity on P-Type GaN

High-reflectance Ohmic Contacts to P-Gan of GaN-based Violet LEDs

Fabrication and Characterization of AlGaN-Based UV LEDs with a ITO/Ga2O3/Ag/Ga2O3 Transparent Conductive Electrode

Research and Analysis of ZnO∶Ga Transparent Electrode LED

Light Extraction Efficiency Enhancement of GaN-based Blue LEDs Based on ITO/ InxO Ohmic Contacts with Microstructure Formed by Annealing in Oxygen.

High-output power GaN-LED based on surface plasmon enhancement

Study on ITO/Ag/ITO multilayer film as the electrode of organic light-emitting diodes

The Effect of p-InGaN layer on ITO based ohmic contacts to p-GaN

High-Performance Gan-Based Leds with Azo/Ito Thin Films As Transparent Contact Layers

Optimization of annealing conditions for Ag/p-GaN ohmic contacts

A Novel Ni/Ag/Pt Ohmic Contact to P-Type GaN for Flip-Chip Light-Emitting Diodes

Study of Top Ito Nano-Gratings on Gan Leds

Synthesis and Characterization of Indium Tin Oxide Nanowires with Surface Modification of Silver Nanoparticles by Electrochemical Method

Enhanced performance of GaN-based ultraviolet light emitting diodes with ITO/graphene/ITO transparent conductive layer