Abstract:In this study, ZrB2/Al7085 nanocomposites were fabricated by in-situ reaction with KBF4 and K2ZrF6 fluoride powders during casting, then hot deformation and heat treatment were applied to the sheet product. The deformation by hot rolling was employed to change the distribution of second phases and ZrB2 nanoparticles and significantly improve the microstructure of the matrix. TEM results indicate the semi-coherent relationship between ZrB2 particle and α-Al on the interface without intermediate products. The contributions of ZrB2 particles on composite are described by refining Al7085 grain size to 47% as heterogeneous nuclei during solidification and accelerating to decrease the residual stress and reduce anisotropy during heat treatment. Meanwhile, Al3Zr precipitate in composites is refined to half size in Al 7085. Compared to the Al7085, mechanical property on composite is enhanced when the ZrB2 volume fraction achieves 1% after quenching with 465 °C−10 min and artificial aging of 120 °C−5 h/160–10 h. The strengthening mechanisms are grain refinement, coefficient of thermal expansion, Orowan strengthening, and load transfer effect and corresponding strengthening contributions are 3.6 MPa,7.7 MPa,20 MPa, and 2.7 MPa. Our study shows the roles of ZrB2 particles act on composite in different processing statuses and provides the basic strengthening way caused by ZrB2 nanoparticles. Our study shows the roles of ZrB2 particles act on composite in different processing statuses and provides the basic strengthening way caused by ZrB2 nanoparticles.

Microstructural evolution of ZrB2–MoSi2 composites during heat treatment

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Effect of high temperature heat treatment on ZrB2-SiC composites added with Yb2O3

Microstructure Evolution and Failure Mechanism of Cr-coated Zry-4 in Air and Steam at 1200 °C

Preparation And Mechanical Properties Of Zrb2-Based Laminated Composites

Preparation and characterization of high-toughness ZrB2/Mo composites by hot-pressing process

Microstructure and oxidation response of Mo-Si-B-ZrB 2 alloy at 900 °C: Effect of pre-oxidation treatment

Preparation and Mechanical Properties of Laminated Zirconium Diboride/molybdenum Composites Sintered by Spark Plasma Sintering

Microstructure evolution and mechanical properties of in-situ ZrB2/Al7085 nanocomposites during hot rolling deformation

Microstructures and mechanical properties of reactive spark plasma-sintered ZrB2–SiC–MoSi2 composites

A TEM study of nanostructures and interfaces in the hot-press sintered ZrB2–SiC–Si3N4 composites

Microstructure, Mechanical, and Thermal Properties of in Situ-Synthesized (zrb2+sic)/zr2[al(si)]4c5 Composites

Microstructural Evolution of Irradiated Cr-Coated Zr-4 under In Situ Transmission Electron Microscopy Heating

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

Toughness Mechanism of Layered ZrB2 Based Composite Ceramic

High-temperature deformation of ZrB2 ceramics with WC additive in four-point bending

Effect of heat treatment on the microstructure, mechanical properties and fracture behaviors of ultra-high-strength SiC/Al–Zn–Mg–Cu composites

Temperature‐dependent mechanical and oxidation behavior of in‐situ formed ZrN/ZrO2‐containing Si3N4‐based composite

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Microstructure, Mechanical Properties and Oxidation Behavior of Reactive Hot-Pressed (Zr,Ti)B2-SiC-ZrC Composites

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride