Abstract:Chemical vapor deposition (CVD) is a promising technique for the preparation of W-based plasma-facing materials (PFMs). An overview of the microstructure, chemical composition, thermal conductivity, thermal stability, thermal shock performance under disruption-like and edge localized mode-like transient heat load, and neutron irradiation performance of CVD-W has been given in our previous work. However, for fusion applications, additional properties need to be assessed. To this end, deuterium (D) permeability, D plasma irradiation performance, and thermal fatigue resistance of CVD-W were investigated in this work. The results showed that the D permeability of CVD-W in the temperature range of 973–1173 K was larger than that of the commercial pure W, which was related to the columnar grain structure of CVD-W. Additionally, both CVD-W and commercial pure W were exposed to D plasma up to a fluence of 1 × 1026 m−2. Compared to commercial pure W, CVD-W exhibited a mitigated blistering behavior and lower D total retention, which could be attributed to its strong [001] crystallographic texture along the thickness direction and a lower number of defect density (e.g. grain boundaries). CVD-W and commercial pure W were also exposed to steady-state and transient heat load simultaneously, leading to a base surface temperature and surface temperature increase of about 953–1473 K and 250–300 K, respectively. A strong grain orientation dependence of the surface degradation induced by the combined heat load has been found. Consequently, CVD-W exhibited a much more uniform plastic deformation than pure W, and no surface cracks along grain boundaries were observed in CVD-W. Finally, the industrial-scale production of CVD-W-based PFMs and mockups was demonstrated. This work paves the way for the fusion applications of thick CVD-W coatings.

Surface Analysis of VPS-W Coatings Boronized by an ICRF Discharge in HT-7

Retention Behavior Of Deuterium And Oxygen In Boronized Vps-W

Blistering Behavior and Deuterium Retention in Tungsten Vanadium Alloys Exposed to Deuterium Plasma in the Linear Plasma Device STEP

Chemical States and Deuterium Retention Behavior of Vacuum Plasma Sprayed Tungsten Coatings

Recent Studies of Tungsten-Based Plasma-Facing Materials in the Linear Plasma Device STEP

Influence of Li and B Coatings of Metal Walls on Deuterium Retention and Plasma Confinement in HT-7

Surface Modification and Deuterium Retention of High Energy Rate Forging W-Y2O3exposed to Deuterium Plasma

Surface Modification of W–V Alloy Exposed to High Heat Flux Helium Neutral Beams

Deuterium Blistering in Tungsten and Tungsten Vanadium Alloys

Recent progress of thick tungsten coating prepared by chemical vapor deposition as the plasma-facing material

Properties of boron layers deposited during boronisations in W7-X

Surface Diversifying and Deuterium Retention Characteristics of Doped Graphite with SiC Coating Exposed to Plasma Discharges in EAST Tokamak

Hydrogen Behaviors at the Near-Surface Region of Tungsten: A First-Principles Study

Electron-Beam Synthesis and Modification and Properties of Boron Coatings on Alloy Surfaces

Directly-cooled VPS-W/Cu limiter and its preliminary results in HT-7

Fuzz Nanostructure and Erosion on Tungsten–vanadium Alloys Exposed to Helium Plasma in the STEP Linear Plasma Device

Surface Blistering and Deuterium Retention in Chemical Vapor Deposition Tungsten Exposed to Deuterium Plasma

Influence of material type and surface roughness of substrate on boronization and its performance

Experimental Study on Boron Carbide Coating Prepared by Electromagnetically Accelerated Plasma Spraying

IRRADIATION EXPERIMENTS OF PLASMA FACING MATERIALS DEVELOPED FOR HT-7U IN THE HT-7 TOKAMAK

Surface modification and deuterium retention in hot-rolled potassium doped tungsten alloy exposed to deuterium plasma