Abstract:<p>High borated steel sheets containing 0.25 wt% to 4.0 wt% boron including hypoeutectic (0.28 wt% B and 2.11 wt% B), eutectic (2.43 wt% B) and hypereutectic (4.01 wt% B) compositions were tried to be fabricated by a novel strip casting technology, and the effects of boron content on sub-rapid solidification behavior and subsequent microstructural evolution together with mechanical properties was studied. It was found that the morphology of borides depended greatly on the boron content. When increasing boron, the morphological change of borides was network-like → grainy → cluster-like → plate-like. Various orientation relationships between different morphological borides and γ-Fe in as-cast steels were also identified. After subsequent hot-rolling and solution-treating, ultra-fine (<10 μm) borides were obtained in hypoeutectic and eutectic steels. Benefiting from that, excellent mechanical properties was achieved, which was much better than that of steels prepared by traditional ingot casting. Particularly, when the boron content approached eutectic composition, of which the effect on the microstructure and mechanical properties was more sensitive. The steels containing 2.11 wt% and 2.43 wt% boron exhibited different morphological borides with a total elongation of 14.1% and 8.0%, respectively. Moreover, a thin hypereutectic borated steel sheet was also prepared, but the borides were very large and the total elongation was very low. The correlation between microstructure and strength was clarified based on the Hall-Petch behavior and intermetallic strengthening effect. Smaller γ-grains and higher volume fraction of borides were responsible for higher strength. The plastic behavior of steels was influenced by strain-hardening rate that was determined by the volume fraction of γ-Fe matrix. A better sustainable strain-hardening capability was beneficial to extend the stage of uniform deformation and enhance the ductility. In addition, the mechanical properties of steels were also decided by the fracture mechanism that was dominated by the size of borides.</p>

Boriding of tungsten by the powder-pack process: Phase formation, growth kinetics and enhanced neutron shielding

Boriding of tungsten by the powder-pack process: Phase formation, growth kinetics and enhanced neutron shielding

Crystal structures and formation mechanisms of boron-rich tungsten borides

Tungsten boride shields in a spherical tokamak

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Phase stability and incompressibility of tungsten boride (WB) researched by in-situ high pressure x-ray diffraction

Preparation of Monophasic Tungsten boride powder from Tungsten and boron carbide

A high temperature W$_2$B cermet for compact neutron shielding

Characterization and Growth Kinetics of Borides Layers on Near-Alpha Titanium Alloys

Synthesis, Phase Evolutions, and Stabilities of Boron-Rich Tungsten Borides at High Pressure.

Effect of boron on the microstructures and properties of 17-4PH/TiC coatings by laser cladding

On the grain boundary strengthening effect of boron in γ/γ′ Cobalt-base superalloys

Effects of boron content on the microstructure and mechanical properties of twin-roll strip casting borated steel sheets

Surface Growth of Boronize Coatings Studied with Mathematical Models of Diffusion

Fabrication and properties of (W+B)/Al hybrid composites for nuclear radiation shielding

Surface evolution and growth kinetics of Ti6Al4V alloy in pack boriding

High entropy alloy borides prepared by powder metallurgy process and the enhanced fracture toughness by addition of yttrium

Thermodynamic Aspects of Powder-Pack Boronizing

Microstructural evolution and mechanical properties of titanium-alloying high borated steel sheets fabricated by twin-roll strip casting

Behavior and mechanism for Boron atom diffusing across tungsten grain boundary in the preparation of WB coating: A first-principles calculation

Reactivity of tungsten tetraboride powders with nickel alloys: Effect of TiAl 3 and Zr additions