Abstract:As a kind of typical human-machine interaction robot,the powered lower-limb exoskeleton driven by hydraulics can augment wearer's power while following wearer.This kind of exoskeleton has a broad application in military field,rescue occasions,and so on,however,there are still many technical difficulties which need to be studied,such as structure optimization.There are 3 kinds of design concepts among the exoskeleton structure design.To guarantee the flexibility and decrease the dead weight of exoskeleton,quasi-anthropomorphic design was adopted,which means the lower-limb exoskeleton is similar to leg but does not need one-to-one match.According to quasi-anthropomorphic design rule,7 degrees of freedom for single leg were set to satisfy the freedom need of wearer.Among these 7 degrees of freedom,only 2 degrees are active which are located in sagittal plane of knee joint and hip joint.During designing the active freedom of knee joint,the core parameters are the size of hydraulic cylinder and the torque which can be produced.So it is significant to study a method which can lead to a minor size of hydraulic cylinder while producing the same torque.To optimize the structure of knee joint and its hydraulic system,the computer aided design (CAD) method and the numerical calculation method were adopted to design the structure of the hydraulic cylinder and its installation position.According to the schematic diagram of structure,the relationship of torque,arm of force,and installation position was built.Design indicators were obtained through analyzing the clinical gait analysis (CGA) data,which was widely used in lower-limb exoskeleton research.To find out the optimized parameter,MATLAB was used to present graphics which depicted the nonlinear relationship which was built before.According to the optimization method,the hydraulic driven knee joint of the lower limb exoskeleton was designed and assembled.During the normal walking phase,there are 2 kinds of torques in knee joint,which contain flexure torque and extension torque.Flexure torque is used to bend shank to avoid the collision of foot and floor while extension torque is used to extend shank to drive the body forward.The both kinds of torques are also important for a person to walk.So simulations were designed to compare the torque produced by hydraulic driven knee joint and the torque needed in normal walking which was got through CGA data.The simulation found that the designed hydraulic driven knee joint could meet the torque demand.Meanwhile,the comparison experiments were also designed and implemented.Hydraulic driven knee joint was driven to follow the motion of wearer in 2 conditions.In the first condition,the wearer just needed to bear the exoskeleton's own weight,which was about 10 kg.In the second condition,another 10 kg load was added on the exoskeleton.It should be noted that all load was transferred to the ground through lower-limb exoskeleton,which meant the added load wouldn't add other burden to wearer.This is the work mechanism of powered lower-limb exoskeleton.In the comparison experiments,the wearer was demanded to move a similar trajectory while it was impossible to move the same trajectory.Experiments showed that the average error was decreased by 0.05％ while the maximum error was increased by 20.7％.Considering the load was increased by 100％ and the motion range was large,these results clear demonstrated how the designed hydraulic driven knee joint satisfied the demand of walking with load.In conclusion,a method is proposed to fulfill the optimization of the knee joint structure of the hydraulic driven lower-limb exoskeleton,and it can obviously instruct other joint design of exoskeleton which is driven by linear actuator such as linear motor and electric cylinder.

Kinematic And Dynamic Performance Of Prosthetic Knee Joint Using Six-Bar Mechanism

Design and Evaluation of a Prosthetic Knee Joint Using the Geared Five-Bar Mechanism

Kinetostatic Analysis For Four-Bar Linkage Mechanism Of Prosthetic Knee Joint

DYNAMIC MODELING AND ANALYSIS OF THE LOWER LIMB PROSTHESIS WITH FOUR-BAR LINKAGE PROSTHETIC KNEE$^{\bf 1)}$

Design, Simulation and Kinematic Validation of a Hip Prosthetic Mechanism with a Multimotor Function

Design, Control, and Validation of a Polycentric Hybrid Knee Prosthesis

A Lightweight Powered Knee Prosthesis Replicating Early-Stance Knee Flexion During Level Walking

Structure design and experiment of knee joint of hydraulic driven lower-limb power-assistance exoskeleton robot

Review of Recent Progress in Robotic Knee Prosthesis Related Techniques: Structure, Actuation and Control

Design and Evaluation of a Novel Microprocessor-Controlled Prosthetic Knee

Research and experiment on active training of lower limb based on five-bar mechanism of man-machine integration system

On the Design of a Powered Transtibial Prosthesis with Stiffness Adaptable Ankle and Toe Joints.

An Adaptive Knee Joint Exoskeleton Based on Biological Geometries.

Mechanism and Controller Design of a Transfemoral Prosthesis with Electrohydraulic Knee and Motor-Driven Ankle

Design, Kinematics and Gait Analysis, of Prosthetic Knee Joints: A Systematic Review

Design, Manufacture, and Experimental Validation of a Hydraulic Semi-Active Knee Prosthesis

Design and Validation of a Polycentric Hybrid Knee Prosthesis With Electromagnet-Controlled Mode Transition

Structure Design and Motion Simulation of a Microprocessor-Controlled Prosthetic Knee

Mechanism Analysis and Optimization Design of Exoskeleton Robot with Non-Circular Gear–Pentabar Mechanism

A Novel Precision Measuring Parallel Mechanism for the Closed-Loop Control of a Biologically Inspired Lower Limb Exoskeleton

Dynamic Model of a 6-DOF Parallel Mechanism with Hooke's Joints at Both Chain Ends