Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Thermal Assisted Ultrasonic Bonding of Multilayer Polymer Microfluidic Devices

Fabrication of Fluidic Chips with 1-D Nanochannels on PMMA Substrates by Photoresist-Free UV-lithography and UV-assisted Low-Temperature Bonding

Low-Temperature Bonding of Poly-(Methyl Methacrylate) Microfluidic Devices under an Ultrasonic Field

Microwave Induced Ethanol Bath Bonding for PMMA Microfluidic Device

Miscible Organic Solvents Soak Bonding Method Use in a PMMA Multilayer Microfluidic Device.

Organic Solvent Fumigation Bonding for Multi-Layer Poly(methyl Methacrylate) Microfluidic Device

Low‐Temperature Thermal Bonding of PMMA Microfluidic Chips

Fabrication of a Three-Dimensional Microfluidic System from Poly(methyl methacrylate) (PMMA) Using an Intermiscibility Vacuum Bonding Technique

Low-pressure Thermal Bonding

Fabrication of 1-d nanochannels on PMMA substrate by photoresist-free uv lithography and UV-assisted bonding under low temperature

PMMA Solution Assisted Room Temperature Bonding for PMMA–PC Hybrid Devices

A simple and low-cost approach for irreversible bonding of polymethylmethacrylate and polydimethylsiloxane at room temperature for high-pressure hybrid microfluidics

New Method of Layer-to-layer Bonding Technology of PMMA

Plasticizer-assisted bonding of poly(methyl methacrylate) microfluidic chips at low temperature.

Rapid Prototyping of Poly(methyl Methacrylate) Microfluidic Systems Using Solvent Imprinting and Bonding.

A microfluidic chip microwave bonding method based on the PMMA

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Fabrication of Micro/nano Fluidic System Combining Hybrid Mask-Mould Lithography with Thermal Bonding

Formation of Embedded Microstructures by Thermal Activated Solvent Bonding

Solvent Bonding of Poly(methyl Methacrylate) Microfluidic Chip Using Phase‐changing Agar Hydrogel As a Sacrificial Layer

Photolamination Bonding for Pmma Microfluidic Chips