Abstract:Reactive melt infiltration (RMI) has been proved to be one of the most promising technologies for fabrication of C/SiC composites because of its low cost and short processing cycle. However, the poor mechanical and anti-ablation properties of the RMI-C/SiC composites severely limit their practical use due to an imperfect siliconization of carbon matrixes with thick walls and micron-sized pores. Here, we report a high-performance RMI-C/SiC composite fabricated using a carbon fiber reinforced nanoporous carbon (NC) matrix preform composed of overlapping nanoparticles and abundant nanopores. For comparison, the C/C performs with conventional pyrocarbon (PyC) or resin carbon (ReC) matrixes were also used to explore the effect of carbon matrix on the composition and property of the obtained C/SiC composites. The C/SiC derived from C/NC with a high density of 2.50 g cm -3 has dense and pure SiC matrix and intact carbon fibers due to the complete ceramization of original carbon matrix and the almost full consumption of inspersed silicon. In contrast, the counterparts based on C/PyC or C/ReC with a low density have a little SiC, much residual silicon and carbon, and many corroded fibers. As a result, the C/SiC from C/NC shows the highest flexural strength of 218.1 MPa and the lowest ablation rate of 0.168 μm s -1 in an oxyacetylene flame of ~ 2200 °C with a duration time of 500 s. This work opens up a new way for the development of high-performance ceramic matrix composites by siliconizing the C/C preforms with nanoporous carbon matrix

The Mechanical Property of C/C Composites Modified by SiCNF

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

3C-SiC Nanowires In-Situ Modified Carbon/Carbon Composites and Their Effect on Mechanical and Thermal Properties

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

EFFECT OF CARBON NANOFIBERS ADDITION ON DENSIFICATION AND MECHANICAL PROPERTIES OF CARBON/CARBON COMPOSITES

Carbon-bonded Carbon Fiber Composites Containing Uniformly Distributed Silicon Carbide

Mechanical properties and wear resistance of Cf / epoxy resin composites with in-situ grown SiC nanowires on carbon fibers

Enhanced thermal and mechanical properties of optimized S i C f / S i C composites with in-situ CNTs on PyC interface

Effects of in situ formed nanostructures on the structure and properties of C/SiOC composites

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Significant Improvement of Mechanical Properties of SiC-Nanowire-Reinforced SiCf/SiC Composites via Atomic Deposition of Ni Catalysts

Effect of SiC content on the mechanical behaviour of a three-dimensional needled C/SiC composite

Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Effect of CNT impregnation on the mechanical and thermal properties of C/C-SiC composites

Mechanical and thermal shock properties of C f /SiBCN composite: Effect of sintering densification and fiber coating

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

Effect of SiCnws on flexural strength of SiCf/HfC-SiC composites after impact and ablation