Abstract:The high-temperature wear resistance plays an important role for Ti–6Al–4V alloy components working in extreme environments, especially vital for avoiding unexpected failure. However, the reasonable method of surface modification should meet the requirement of improving in wear resistance and less decreasing in mechanical properties simultaneously, which brings a great challenge. In the present research, the laser shock peening (LSP) technique was applied to optimize the superficial layer of Ti–6Al–4V alloy by different processing. The microstructure, elastic modulus, nano-hardness and high-temperature tribology properties of the LSP processed Ti–6Al–4V were investigated to reveal the improving effect. The results demonstrate the LSP processing transforms the dual-size grain structure to relative homogeneous grain structure and forms the gradient nano-structure in superficial layer. With the increasing of LSP processing numbers, the density of geometrically necessary dislocation (GND) decreases obviously, but the density of statistically stored dislocation (SSD) rises significantly, which promotes the increase of total dislocation density compared with the as-received (AR) alloy. Due to the crystal evolution, the Ti–6Al–4V alloy with three-times LSP processing has the lowest wear rate which is less than half of the as-received state. The observations on worn surface and adjacent cross-sectional microstructure reveal the severe scratching and many inner microcracks in the AR sample but the slight scraping and few inner microcracks in the three-times LSP processed sample. Considering the elevated nano-hardness and elastic modulus, the improved tribological properties should be mainly attributed to the optimized microstructure and dislocation state by LSP processing. The present research provides a more reasonable method to improve the high-temperature wear properties of Ti–6Al–4V alloy.

Experimental Study of High-power Pulsed Laser Induced Shock Waves in Ti Alloy Target

Experimental Study of Shock Waves Induced by High-Power Pulsed Laser in Az31b Magnesium Alloy

Experimental study on the pressure characteristics of laser-induced shock waves under different energy distribution

The Spatio-Temporal Evolution of Shock Wave Pressure Induced by Laser: Effects of Laser Parameters and Confinement Layer

Studies on Laser Shock Peening on Nanomechanical and Mechano-Chemical Properties of Titanium Alloy (Ti6Al4V)

Investigation on the deformation progress and residual stress of Ti-6Al-4V alloy during laser shock peening

Microscopic Phase Change of Ni-Ti Shape Memory Alloy Target under Femto-second Laser Ablating

Femtosecond Laser Ablation of Ti Alloy and Al Alloy

Microstructure evolution and electroplasticity in Ti64 subjected to electropulsing-assisted laser shock peening

Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening

Experimental and Thermal Stress Field Numerical Simulation Study on Laser Metal Deposition of Ti-48Al-2Cr-2Nb Alloy

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

Abnormal Softening of Ti-metallic Glasses During Nanosecond Laser Shock Peening

Dynamic Analysis of Laser Shock Response: Experimental and Numerical Studies

Formation mechanism of residual stress hole under different pulse durations and shock pressure distributions in Ti6Al4V alloy during laser peen texturing

Laser shock processing of titanium alloys: a critical review on the microstructure evolution and enhanced engineering performance

Experimental and Numerical Studies of Fatigue Behavior of Ti6Al4V Alloy Treated by Laser Shock Peening

Mechanical properties and strengthening mechanisms of Ti-6Al-4V treated by electro-pulsing assisted laser shock peening

Temporal Evolution of Pressure Generated by a Nanosecond Laser Pulse Used for Assessment of Adhesive Strength of the Tungsten-Zirconium-Borides Coatings

Microstructure and High-Temperature Tribological Properties of Ti–6Al–4V Alloy Treated by Laser Shock Peening

Preparation of TiC-doped W-Ti Alloy and Heat Flux Performance Test under Laser Beam Facility