Abstract:Mechanical test of materials and structures commonly used in micro-electro-mechanical systems (MEMS) is an essential step towards the achievement of optimal design and reliability of the micro mechanical components. The measurement of the occurring mechanical quantities, such as forces and deformations, requires the development of new testing procedures. Non-contact and whole-field optical measuring and inspection methods are a unique technology for the measurement of the shape and deformation of MEMS materials and components. In recent years, substantial research has been carried out on micro-sensors, micro-mirrors, micro-motors, micro-pumps, micro- valves, micro-actuators, micro-lenses, and so on. The diameter of spherical lens is about 250 μm, the size of micro-motor is no more than 800 μm, an inlet port size is only 80 μm. Under Scanning Electronic Microscope (SEM) and Atomic Force Microscope (AFM) sub-micron displacement can be resolved. But, to loading on the sample is more difficult and the deformation measurement range is limited. Optical methods are introduced for the small sample testing of MESM materials and structures in this paper. The methods are based on the laser interferometry, phase shifting, digital image correlation and image processing etc. Using a LWDM (long working distance microscope) and digital speckle correlation method (DSCM) the stretching strain of a thin copper wire (diameter 0.1 mm) can be determined. The proposed technique is also applicable for measuring other MEMS materials that may be even smaller or thinner than that used in this paper. The interference of light beams of equal path difference is used for the measurement of the Young's modulus of a micro-beam. An optical wedge which consists of an optical plate and a micro-beam which forms part of a micro-accelerometer is illuminated by a collimated monochromatic sodium light beam. Loading on the micro-beam is accomplished by a loading-pin mounted on a 3-axis translation-stage and the resulting interference fringe pattern is observed using a CCD camera connected to a computer. Loadings are recorded using a high sensitive load cell that measures loads of up to 200 g with a resolution of 0.01 g. This paper also describes the use of optical fringe projection method for 3-D surface profile measurement of small objects. In this method, sinusoidal linear fringes are projected on the object surface by a sinusoidal grating phase shifting projector and a LWDM. The image of the fringe pattern is captured by another LWDM and a CCD camera and processed by phase-shifting techniques. A simple procedure is described which enables calibration of the optical set-up for subsequent quantitative measurement of unknown object shapes and deformations. The method developed can also be applied to the measurement of the warpage of a small component under thermal loading. This method is relatively simple and accurate, and is capable of conducting fully automated measurements. The deformation of a micromirror (100 μm × 100 μm) driven by an electrostatic force is measured by comparing the profiles between deformed and undeformed. The maximum displacement of micro mirror is no more than 2 microns. Thus, the rotation angle of the micromirror is less 2 degrees. Experimental results obtained demonstrate the feasibility of the proposed method to be used for evaluating the contouring of the microstructure.

Development of an Integrated Optical System for Warpage and Hermeticity Test of Microdisplay

Digital testing of transmitted wavefront distortion for micro-optics

Surface defects evaluation system based on electromagnetic model simulation and inverse-recognition calibration method

Warpage measurement using projection speckle correlation method and microscopic interferometry

Recent Developments of Interferometric Wavefront Sensing

ADVANCED OPTICAL MEASUREMENT TECHNOLOGY IN THE SEMICONDUCTOR AND MEMS

Optical Full-Field Technique for Measuring Deformation on Micromechanical Components

Advanced Mechanical/Optical Configuration of Real-Time Moiré Interferometry for Thermal Deformation Analysis of Fan-Out Wafer Level Package

Study of Thermal Deformation of Microelectronics Packaging Product by Interferometric Technique

CONSTRUCTION AND ACCURACY TEST OF A NOVEL HETERODYNE GRATING INTERFEROMTER SYSTEM FOR TWO-DIMENSIONAL DISPLACEMENT MEASUREMENT

Towards the Development of a Hybrid-Integrated Chip Interferometer for Online Surface Profile Measurements.

Quantitative Phase Measurement for Wafer-Level-Optics

Thermal optics property study and athermal design on optical window of IR aiming device reliability testing system

Warpage Characterization of a Large Size Fan-out Panel Subjected to Inhomogeneous Heating by a Digital Fringe Projection System

Development of Micro-scale Displacement and Profile Measurement Systemand its Applications

Optical Methods for the Measurement of Mems Materials and Structures

Integrated form-position measurement of large-aperture transparent elements based on stereoscopic phase measuring deflectometry

Study on Defromation of a Micro Beam Using Interferometry

MEMS Test System Based on Virtual Instrument Technology

Microscopic Interferometry for Dimensional Characterization of MEMS Devices

Vertical Scanning White-Light Interferometry for Dimensional Characterization of Microelectromechanical System Devices