Low-temperature fabrication of nano-porous TiO2 films for flexible dye-sensitized solar cells

Junying Mu,Juan Xu,Qiushui Liangshi,Hongwei Zhu,Zhenxing Chen

DOI: https://doi.org/10.3969/j.issn.1006-3536.2007.03.012

2007-01-01

Abstract:Properties of flexible dye-sensitized solar cells were briefly introduced,and progress of nano-porous TiO2 semiconductor films fabricated under low temperature were summarized.

What problem does this paper attempt to address?

Functions of Self-Assembled Ultrafine TiO2 Nanocrystals for High Efficient Dye-Sensitized Solar Cells

Fengxian Xie,Sheng-Jye Cherng,Shunmian Lu,Ya-Huei Chang,Wei E. I. Sha,Shien-Ping Feng,Chih-Ming Chen,Wallace C. H. Choy

DOI: https://doi.org/10.1021/am5006628

IF: 9.5

2014-01-01

ACS Applied Materials & Interfaces

Abstract:In this paper, we demonstrate a simple approach of self-assembled process to form a very smooth and compacted TiO2 underlayer film from ultrafine titanium oxide (TiO2) nanocrystals with dimension of 4 nm for improving the electrical properties and device performances of dye-sensitized solar cells (DSSCs). Because the TiO2 film self-assembles by simply casting the TiO2 on fluorine-doped tin oxide (FTO) substrate, it can save a lot of materials in the process. As compared with control DSSC without the self-assembled TiO2 (SA-TiO2) layer, short-circuit current density (J(sc)) improves from 14.9 mA/cm(2) for control DSSC to 17.3 mA/cm(2) for masked DSSC with the SA-TiO2 layer. With the very smooth SA-TiO2 layer, the power conversion efficiency is enhanced from 8.22% (control) to 9.35% for the DSSCs with mask and from 9.79% (control) to 11.87% for the DSSCs without mask. To explain the improvement, we have studied the optical properties, morphology, and workfunction of the SA-TiO2 layer on FTO substrate as well as the impedance spectrum of DSSCs. Importantly, we find that the SA-TiO2 layers have better morphology, uniformity, and contact with FTO electrode, increased workfunction and optical transmission, as well as reduced charge recombination at the contact of FTO substrate contributing to the improved device performances. Consequently, our results show that the simple self-assembly of TiO2 ultrafine nanocrystals forms a very good electron extraction layer with both improved optical and electrical properties for enhancing performances of DSSCs.
A Novel Nanocrystalline TiO 2 Thin Film Electrodes Prepared at Low Temperature

Cy Li,Xp Li,Yt Ma,Zp Wang,Xw Zhou,Y Lin,Sj Feng,Xr Xiao

2005-01-01

Abstract:Nanocrystalline TiO2 thin films were successfully prepared by a new "water-cooked" method on both conductive glass substrates and flexible substrates at low temperature. Dye-sensitized solar cells based on these films have exhibited high overall light-to-electricity conversion efficiencies of 4.67 % and 1.94 % on conductive glass substrate and flexible substrate, respectively, under the illumination at 100 mW/cm(2).
Low Temperature Transferring of Anodized Tio2 Nanotube-Array Onto A Flexible Substrate for Dye-Sensitized Solar Cells

Shu Zhu,Xiaolin Liu,Jia Lin,Xianfeng Chen

DOI: https://doi.org/10.1364/ome.5.002754

2015-01-01

Optical Materials Express

Abstract:In this paper, free-standing TiO2 nanotube membranes are transferred onto ITO/PET substrates using binder-free TiO2 pastes. Followed by laser sintering, the electrical contacts between the TiO2 nanotube membrane, nanoparticles and substrate can be efficiently promoted, which prevents from damaging to the plastic conductive substrate. The efficiency of 4.65% is achieved without traditional high temperature sintering and mechanical compression, which shows great potential application in TiO2 nanotube based flexible dye-sensitized solar cells (DSSCs). (C)2015 Optical Society of America
Low‐Temperature Preparation of Hierarchical Structure TiO2 for Flexible Dye‐Sensitized Solar Cell

Peng Zhang,Congcong Wu,Yongsheng Han,Tetsuro Jin,Bo Chi,Jian Pu,Li Jian

DOI: https://doi.org/10.1111/j.1551-2916.2011.04984.x

IF: 4.186

2011-01-01

Journal of the American Ceramic Society

Abstract:Photoanodes for flexible DSSC have been prepared through a chemical sintering method using hydrothermal cement at low temperature of 120°C. The addition of the hydrothermal cement can effectively increase the adhesion between the photoanode and flexible ITO‐PET substrate and build the interconnection between nanoparticles at low temperature for the fast transport of electrons. The flexible DSSC based on the photoanode obtains a relatively high photo‐to‐electric conversion efficiency of 4.0%. The method basing on the commercially available TiO2 with a small proportion of hydrothermal cement is suitable for roll‐to‐roll screen‐printing preparation, which is expected to be scaled up for mass production of high performance flexible DSSCs.
Preparation and Properties of Flexible Dye-Sensitized Solar Cells

Yuan Lin,NianQing Fu,Shanghua Wang,WeiWei Tan

2012-01-01

Abstract:Flexible dye-sensitized solar cell has attracted much attention due to its advantages of low cost and easy production. Flexible dye-sensitized solar cell comprised of a nanocrystalline TiO2 film electrode based on Ti-metal substrate and a counter-electrode based on plastic substrate is investigated. In order to improve the photovoltaic performance, the different methods including electrophoretic deposition under low DC field, electrochemical anodization by DC and pulse voltages and screen printing in cooperation with high-temperature sintering were employed to prepare Ti substrate based nanocrystalline TiO2 film electrodes and TiO2 nanotube film electrodes, and low-temperature methods of electrochemical deposition and chemical reduction were used to prepare Pt and carbon counter-electrodes on the plastic substrate. The mechanism and characters of these methods and the techniques of optimization were analyzed and discussed. The performance of the nanocrystalline TiO2 film electrodes and counter-electrodes prepared by different methods were measured and evaluated by their photovoltaic behavior measurements. Flexible dye-sensitized solar cells with Ti substrate based TiO2 photoelectrodes and plastic substrate based Pt counter-electrodes prepared by different methods were fabricated. The maximal light to electricity conversion efficiency of 6. 74% was achieved.
Chemical sintering of graded TiO2 film at low-temperature for flexible dye-sensitized solar cells

Xin Li,Hong Lin,Jianbao Li,Ning Wang,Chunfu Lin,Luozheng Zhang

DOI: https://doi.org/10.1016/j.jphotochem.2007.10.010

2008-01-01

Abstract:A mesoporous nanocrystalline graded TiO2 film was prepared on either a transparent conductive glass (ITO/glass) or a transparent conductive polymer (ITO/PEN, PEN=poly(ethylene naphthalene-2,6-dicarboxylate) through a doctor-blade method and then treated by chemical sintering at 150°C. The graded film, which has a large specific surface area, high porosity, and proper strength, was composed of particles with different sizes and appropriate ratios. The effects of the smallest particles for binding and the largest particles for light scattering were studied. High light-to-energy conversion efficiencies of 4.10% and 3.05% were obtained within the dye-sensitized solar cells (DSSCs) fabricated by using the graded films on ITO/glass and ITO/PEN, respectively. The results show that the graded structure has promising applications in DSSCs.
Low-temperature sol-gel synthesized TiO2 with different titanium tetraisopropoxide (TTIP) molarity for flexible emerging solar cell

Nur Syamimi Noorasid,Faiz Arith,Omsri Vinasha Aliyaselvam,Fauziyah Salehuddin,Ahmad Nizamuddin Mustafa,Puvaneswaran Chelvanathan,Mohd Asyadi Azam,Nowshad Amin

DOI: https://doi.org/10.1007/s10971-024-06310-2

2024-02-09

Journal of Sol-Gel Science and Technology

Abstract:The tetragonal crystal structured anatase titanium dioxide (TiO 2 ) has been conventionally used as an electron transport layer in emerging solar cells. Conventionally, a high-temperature process above 450 °C is indispensable to form crystallized TiO 2 films with a well-defined mesoporous structure. Due to the temperature limitations of the flexible polymer substrates, notably below 150 °C, such a high-temperature process is ineffective for flexible emerging solar cells. Currently, cutting-edge and high-potential solar cells are flexible dye-sensitized and perovskite solar cells which are preeminent in mass production due to their roll-to-roll printing technique. Hence, this study explores a low-temperature synthesis of crystallized TiO 2 layers using the sol-gel method with various precursor concentrations of titanium tetraisopropoxide (TTIP). Then, the crystallized TiO 2 was deposited with a simple yet low-cost spin-coat technique on flexible substrates (ITO/PET). A thorough scrutinization of TTIP concentration is crucial in identifying the potential of TiO 2 films through comprehensive studies of elements aspects of structural, optical and electrical properties. The synthesized TiO 2 films with a TTIP concentration of 0.5 M demonstrated a high porosity microstructure with exceptional transmittance, allowing a large number of photons to penetrate and thereby resulting in an enhanced charge carrier conduction mechanism. In addition, the direct optical bandgap is reduced with increasing TTIP molarity, proving the involvement of particle factors influencing photocatalytic activities. Moreover, electrical analysis proved that all the correlation features resulted in remarkably low sheet resistance and conductivity of 0.4 MΩ/sq and 0.1194 mS/cm, respectively. It can be conjectured from this study that the synthesis of crystallized TiO 2 at low-temperature conditions with a certain TTIP molarity is successful and has resulted in an enhancement of the electron conduction mechanism, particularly for flexible emerging solar cell applications.

materials science, ceramics
High Efficiency Flexible Perovskite Solar Cells Using Superior Low Temperature Tio2

Dong Yang,Ruixia Yang,Jing Zhang,Zhou Yang,Shengzhong (Frank) Liu,Can Li

DOI: https://doi.org/10.1039/c5ee02155c

IF: 32.5

2015-01-01

Energy & Environmental Science

Abstract:15.07% efficiency for flexible perovskite solar cells is achieved using low temperature TiO2.
Low-Cost Fabrication of TiO2 Nanorod Photoelectrode for Dye-sensitized Solar Cell Application

Wei Zhang,Rui Zhu,Bin Liu,Seeram Ramakrishna

DOI: https://doi.org/10.1071/ch11144

2011-01-01

Australian Journal of Chemistry

Abstract:One-dimensional nanostructured semiconductor oxides that can provide a direct electron conduction pathway have received increasing attention as photoelectrodes in dye-sensitized solar cells. In this study, a facile and cost-effective method to produce high-quality TiO2 nanofibres is developed based on an electrospinning technique. In particular, poly(ethylene oxide) was selected and proved to be an excellent matrix polymer for electrospinning owing to its low decomposition temperature, wide availability, and environmental friendliness. In addition to obtaining TiO2 nanofibres with well-controlled morphology and pure anatase, the TiO2 grain size could be easily tuned by changing the preparation conditions. Based on the synthesized TiO2 nanofibres, dye-sensitized solar cells were fabricated and a high energy conversion efficiency of 6.44 % was achieved under illumination with air mass 1.5 (100 mW cm–2) simulated sunlight, which demonstrates the great potential of the synthesized TiO2 nanofibres as efficient photoelectrode material for low-cost dye-sensitized solar cells.
Fabrication of Nano-TiO2 Coating for Dye-Sensitized Solar Cell by Vacuum Cold Spraying at Room Temperature

Sheng-Qiang Fan,Chang-Jiu Li,Guan-Jun Yang,Ling-Zi Zhang,Jin-Cheng Gao,Ying-Xin Xi

DOI: https://doi.org/10.1007/s11666-007-9090-z

IF: 2.839

2007-01-01

Journal of Thermal Spray Technology

Abstract:Deposition of nanocrystalline TiO2 coating at low temperature is becoming more attractive due to the possibility for continuous roll production of the coating for assembly lines of dye-sensitized solar cell (DSC) at a low cost. In this study, porous nano-TiO2 coating was deposited by vacuum cold spraying (VCS) at room temperature on a conducting glass substrate using commercial P25 nanocrystalline TiO2 powder. The microstructure of TiO2 coating was characterized by field emission scanning electron microscopy (FESEM) and nitrogen adsorption test. A commercial dye (N719) was adsorbed on the surface of TiO2 particles within the coating to assemble a DSC. The cell performance was evaluated by employing simulated solar light at an intensity of 100 mW/cm(2). The results showed that TiO2 coating was deposited by the agglomerates of nano-TiO2 Powders. The Brunauer-Emmett-Teller (BET) test of the as-sprayed TiO2 coating yielded a porosity of 49% and an average pore size of 17 nm. The assembled solar cell yielded a short-circuit current density of 7.3 mA/cm(2) and an energy conversion efficiency of 2.4%. The test results indicate that VCS was a promising method to deposit nanocrystalline TiO2 coatings at low temperature applied to DSCs.
A novel low-cost, one-step and facile synthesis of TiO2 for efficient fiber dye-sensitized solarcells

Yongping Fu,Ming Peng,Zhibin Lv,Xin Cai,Shaocong Hou,Hongwei Wu,Xiao Yu,Hanny Kafafy,Dechun Zou

DOI: https://doi.org/10.1016/j.nanoen.2012.12.006

IF: 17.6

2013-07-01

Nano Energy

Abstract:In this communication, a novel TiO2 film was synthesized by directly sintering titanium tetraisopropoxide (TTIP) on a titanium wire. The preparation process is simple, fast, facile, low cost and very suitable for large-scale manufacture. Efficiencies of 5% and 7% were achieved, when this material was used as the semiconductor film or the block layer of fiber dye-sensitized solar cells (FDSSCs), respectively. The compact and sturdy TiO2 enables the FDSSCs to maintain a high efficiency during bending and show good flexibility. The use of Pt-modified stainless steel wire as the counter electrode can dramatically reduce the cost of FDSSCs and also keep high efficiency. Utilizing the TiO2 material as the block layer can reduce the recombination, leading to improved conversion efficiency.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Development of Low Temperature Synthesizing Nano-sized Titania Film

YAN Lu-ting,SI Wen-jie,LIU Lian-yun,DAI Chun-ai,ZHENG Yan-peng

DOI: https://doi.org/10.3969/j.issn.1001-4381.2006.z1.132

2006-01-01

Journal of Materials Engineering

Abstract:Titanium dioxide thin film has extensive application in several fields such as photocatalysis,dye-sensitized solar cells,or gas sensor.Low temperature processing has attracted much attention in recent years because that it is useful for the synthesis of crystalline titanium dioxide film having a high surface area on all kinds of substrates.This review deals with the methods for preparation of crystal titanium dioxide thin film at low temperature.
Flexible Solar Cells: Low‐Temperature‐Deposited TiO 2 Nanopillars for Efficient and Flexible Perovskite Solar Cells (Adv. Mater. Interfaces 3/2021)

Zhongwei Wu,Peng Li,Jie Zhao,Ting Xiao,Hong Hu,Peng Sun,Zehan Wu,Jianhua Hao,Chunlin Sun,Haoli Zhang,Zhifeng Huang,Zijian Zheng

DOI: https://doi.org/10.1002/admi.202170016

IF: 5.4

2021-02-01

Advanced Materials Interfaces

Abstract:<p>Sunlight can be converted to electricity via solar cells, with which then light can be generated the other way around. In this regard, skyscrapers performing light show during night or the bright Karst landscape under the ground are exemplified, echoing the geometry of the TiO<sub>2</sub> nanopillars which are fabricated via a low‐temperature dry process and work as the efficient electron‐transporting layer in flexible perovskite solar cells. More details can be found in article number <a href="https://doi.org/10.1002/admi.202001512">2001512</a> by Zhifeng Huang, Zijian Zheng, and co‐workers. </p>

materials science, multidisciplinary,chemistry
Dye-Sensitized Nano-crystalline TiO2 Solar Cells

Gui-qiang WANG,Zhong-jun FU

DOI: https://doi.org/10.3969/j.issn.1672-1179.2005.05.001

2005-01-01

Abstract:The structure and functioning principle of dye-sensitized Nano-crystalline TiO_2 solar cell were discussed. Emphases and the new advancements of dye-sensitized Nano-crystalline TiO_2 solar cell were summarized with 45 references. This new-type solar cell would widely be used in the future for their low cost, high efficiency and simple fabrication.
Interfacial Engineering for Efficient Low-Temperature Flexible Perovskite Solar Cells.

Kui Zhao,Jiangshan Feng,Yachao Du,Zhichao Wang,Pengchen Zou,Shiqiang Wang,Shumei Wang,Chou Liu,Weilun Cai,Tinghuan Yang,Jianxi Yao,Zicheng Ding,Sheng Liu,Xin Chen,Xu Pan,Yajie Wang,Wenliang Huang,Nan Wu,Guangtao Zhao

DOI: https://doi.org/10.1002/anie.202309398

2023-08-25

Angewandte Chemie

Abstract:Photovoltaic technology with low weight, high specific power in cold environments, and compatibility with flexible fabrication is highly desired for near-space vehicles and polar region applications. Herein, we demonstrate efficient low-temperature flexible perovskite solar cells by improving the interfacial contact between electron-transport layer (ETL) and perovskite layer. We find that the adsorbed oxygen active sites and oxygen vacancies of flexible tin oxide (SnO2) ETL layer can be effectively decreased by incorporating a trace amount of titanium tetrachloride (TiCl4). The effective defects elimination at the interfacial increases the electron mobility of flexible SnO2 layer, regulates band alignment at the perovskite/SnO2 interface, induces larger perovskite crystal growth, and improves charge collection efficiency in a complete solar cell. Correspondingly, the improved interfacial contact transforms into high-performance solar cells under one-sun illumination (AM 1.5G) with efficiencies up to 23.7% at 218 K, which might open up a new era of application of this emerging flexible photovoltaic technology to low-temperature environments such as near-space and polar regions.

Engineering,Medicine,Materials Science,Physics
Flexible Dye-Sensitized Solar Cells with TiO2 Film Deposited on ITO/SiOx/Metal Foil Substrate

Man Gu Kang,Nam -Gyu Park,Kwang Sun Ryu,Soon Ho Chang,Kang-Jin Kim

DOI: https://doi.org/10.1149/ma2005-01/2/92

2006-02-22

ECS Meeting Abstracts

Abstract:Abstract not Available.
THE RESEARCH PROGRESS OF NANO-POROUS TiO_2 FILMS IN DYE-SENSITIZED SOLAR CELLS

Zeng Longyue,Dai Songyuan,Wang Kongjia,Kong Fantai

2005-01-01

Abstract:The study progress of the semiconductor films was introduced from the two aspects: the mechanism and fabrication of the solar cells. Some problems of the semiconductor films reducing the efficiency of the solar cells were pointed out, the possible solvent were also presented.
Low-temperature synthesis of stable nanoTiO2-rGO composite colloids and their application in photoelectric films

Hanyang Gao,Wei Chen,Jian Yuan,Zhi Jiang,Guoxin Hu,Wenfeng Shangguan,Yangzhou Sun,Jiachun Su

DOI: https://doi.org/10.1039/c3ra23095c

IF: 4.036

2013-01-01

RSC Advances

Abstract:It is found that low-temperature synthesized nanoTiO(2) particles and reduced graphene oxide (rGO) would make up for each other's shortcomings: on the one hand, negatively charged nanoTiO(2) particles could obviously enhance the dispersion of rGO. The nanoTiO(2)-rGO colloid synthesized at a low temperature (95 degrees C) remained stable for at least 6 months; on the other hand, for the ultrathin and transparent nanoTiO(2)-rGO films prepared using this stable colloid, rGO loading could enhance the connection of the nanoTiO(2) particles and the substrate and therefore effectively increase the photocurrent to 4.8 times more than the photocurrent generated by pure nanoTiO(2). The as-prepared transparent flexible film can be shaped into triangular calandrias which could make full use of the incident UV light, and thus increase the removal efficiency from the pass through of gas-phase acetaldehyde.
Low Temperature Fabrication of High Performance P-N Junction on the Ti Foil for Use in Large-Area Flexible Dye-Sensitized Solar Cells

Yaoming Xiao,Jihuai Wu,Jianming Lin,Miaoliang Huang,Leqing Fan,Zhang Lan,Gaoyi Han,Sidian Li

DOI: https://doi.org/10.1016/j.electacta.2013.11.096

IF: 6.6

2013-01-01

Electrochimica Acta

Abstract:A p-n junction of poly (3,4-ethylenedioxythiophene) (PEDOT) - dye-sensitized TiO2 is introduced into the large-area flexible dye-sensitized solar cell (DSSC) as an anode. This p-n junction is fabricated using a cyclic voltamrnetry electropolyrnerization of PEDOT onto a Ti foil substrate, and then treated in the aqueous ammonia, finally subjected to coating TiO2 by a doctor-scraping technique, all of preparations and treatments are carried out under low temperature. The obtained p-n junction forms a single directional pathway for electron transport which benefites the charge separation. The large-area (10 cm(2)) flexible DSSC with the p-n junction demonstrates an enhanced photovoltaic conversion efficiency of up to 6.51% compared to 4.89% for the DSSC without the p-n junction due to its low series resistance and charge-transfer resistance, high effective electron lifetime for recombination. As a result, the DSSC fabricated using the p-n junction can be suitable for high powered DSSC applications. (C) 2013 Elsevier Ltd. All rights reserved.
A Bifunctional TiO2 Sol for Convenient Low-Temperature Fabrication of Dye-Sensitized Solar Cells

Wei Chen,Yangqiao Liu,Jianqiang Luo,Jing Sun,Lian Gao

DOI: https://doi.org/10.1016/j.matlet.2011.09.020

IF: 3

2012-01-01

Materials Letters

Abstract:A TiO2 sol was synthesized and acted as a precursor of TiO2 nanoparticles in the application of low temperature dye-sensitized solar cells. It can also be used as an interparticle binder in the TiO2 mesoprous films. The overall efficiency of the cell with sol addition was found to be 13% higher than the one without it and achieved 4.41% under irradiation of 100mW/cm2 AM1.5 sunlight. Electrochemical impedance spectra were applied to analyze the internal resistance changes of the cells with and without sol. Fine particles in the sol were proven to increase the electron life-time by improving the interconnectivity of the main particles.

Low-temperature fabrication of nano-porous TiO2 films for flexible dye-sensitized solar cells

Functions of Self-Assembled Ultrafine TiO2 Nanocrystals for High Efficient Dye-Sensitized Solar Cells

A Novel Nanocrystalline TiO 2 Thin Film Electrodes Prepared at Low Temperature

Low Temperature Transferring of Anodized Tio2 Nanotube-Array Onto A Flexible Substrate for Dye-Sensitized Solar Cells

Low‐Temperature Preparation of Hierarchical Structure TiO2 for Flexible Dye‐Sensitized Solar Cell

Preparation and Properties of Flexible Dye-Sensitized Solar Cells

Chemical sintering of graded TiO2 film at low-temperature for flexible dye-sensitized solar cells

Low-temperature sol-gel synthesized TiO2 with different titanium tetraisopropoxide (TTIP) molarity for flexible emerging solar cell

High Efficiency Flexible Perovskite Solar Cells Using Superior Low Temperature Tio2

Low-Cost Fabrication of TiO2 Nanorod Photoelectrode for Dye-sensitized Solar Cell Application

Fabrication of Nano-TiO2 Coating for Dye-Sensitized Solar Cell by Vacuum Cold Spraying at Room Temperature

A novel low-cost, one-step and facile synthesis of TiO2 for efficient fiber dye-sensitized solarcells

Development of Low Temperature Synthesizing Nano-sized Titania Film

Flexible Solar Cells: Low‐Temperature‐Deposited TiO 2 Nanopillars for Efficient and Flexible Perovskite Solar Cells (Adv. Mater. Interfaces 3/2021)

Dye-Sensitized Nano-crystalline TiO2 Solar Cells

Interfacial Engineering for Efficient Low-Temperature Flexible Perovskite Solar Cells.

Flexible Dye-Sensitized Solar Cells with TiO2 Film Deposited on ITO/SiOx/Metal Foil Substrate

THE RESEARCH PROGRESS OF NANO-POROUS TiO_2 FILMS IN DYE-SENSITIZED SOLAR CELLS

Low-temperature synthesis of stable nanoTiO2-rGO composite colloids and their application in photoelectric films

Low Temperature Fabrication of High Performance P-N Junction on the Ti Foil for Use in Large-Area Flexible Dye-Sensitized Solar Cells

A Bifunctional TiO2 Sol for Convenient Low-Temperature Fabrication of Dye-Sensitized Solar Cells