Abstract:The corrosion and scaling phenomenon have crucial impact on drinking water distribution systems (DWDS), which might lead to pipe blockage or leakage, colored water and other chemical stability issues. In this study, a simulating pipe system with continuous water flow was prepared to investigate the characteristics of corrosion and scaling on ductile iron pipe transporting ground water with sodium-hypochlorite (NaOCl) disinfection. Electrochemical assays, such as polarization curves and electrochemical impedance spectra were applied to monitor the corrosion and scaling process. Results showed the morphology and components of scale were closely related with the electrochemical analysis results. The corrosion current density decreased continuously as corrosion and scaling proceeded. The process could be divided into three stages. During Stage I (0-20 days), the corrosion current intensity of low NaOCl dosage experiments (1, 2 mg/L) were higher than those of high NaOCl dosage experiments (5, 10 mg/L). The difference could be explained by different oxidation potentials, pH and CaCO3 deposition. During Stage II (20-80 days), higher proportions of Fe3O4 in scale in experiments with no or low NaOCl dosages restrained the corrosion process and presented smaller corrosion current. Subsequently, the ductile iron surface became passivated and the difference of various NaOCl dosages affecting corrosion and scaling process turned to be negligible during Stage III (80-90 days). A negative linear relationship between the proportion of stable scale component and the corrosion current density was established. Besides the direct corrosion reaction with iron substrate, NaOCl dosing was accompanied by an increase in pH and calcium carbonate precipitation potential values, which affected the early period corrosion and scaling phenomenon greatly. (C) 2020 Elsevier Ltd. All rights reserved.

Corrosion and Scaling on Carbon Steel and Galvanized Steel Pipe in Simulated Geothermal Water

Scaling and Corrosion of 304 Stainless Steel and Galvanized Steel Pipes in a Simulated Geothermal Water Environment

Corrosion and Scaling of the Galvanized Steel Pipe in Flowing Geothermal Water

Experiment of stainless steel corrosion and scaling in geothermal water supply pipeline

Effect of Ca2+ and Mg2+ on Corrosion and Scaling of Galvanized Steel Pipe in Simulated Geothermal Water

Scaling and electrochemical corrosion behavior of 304 stainless steel pipes in a simulated geothermal water environment

Corrosion Failures of High Temperature Heat Pipes

Research of the Scaling and Corrosion Tendency of Geothermal Well Waters in the Main Urban Area of Chongqing

Geothermal Water Corrosion and Scaling Characteristics Analysis: A Case Study of Reshuiwei Geothermal Field

Corrosion Of Carbon Steel In Typical Water Environments Of Thermal Power Plant

Anti-scaling Performance of PPS Composite Coatings in a Circulated and Simulated Geothermal Water Environment

An Experimental Investigation on the Relation between Corrosion and Thermohydraulic Behavior in Heat Exchangers for Geothermal Applications

Anticorrosion and Scale Behaviors of Nanostructured ZrO2–TiO2 Coatings in Simulated Geothermal Water

Physico-chemical Characteristics of Corrosion Scales from Different Pipes in Drinking Water Distribution Systems

Corrosion Electrochemical Behavior of 20 Steel and 16Mn Steel in Simulated CO2 Flooding Environment

Early Period Corrosion and Scaling Characteristics of Ductile Iron Pipe for Ground Water Supply with Sodium Hypochlorite Disinfection.

Investigation of Scaling and Materials' Performance in Simulated Geothermal Brine

Characteristics of Iron Corrosion Scales and Water Quality Variations in Drinking Water Distribution Systems of Different Pipe Materials.

Anti-scaling characterization of PTFE/PPS composite coating in the geothermal water environment

Study on Under-Deposit Corrosion Behavior of X65 Steel in Simulated CO2 Saturated Produced Water