Abstract:The Al63Cu25Fe9Cr3 quasicrystalline was prepared by conventional casting method. The microstructures and phase composition of Al63Cu25Fe12 quasi-crystalline and Al65Cu20Fe10Cr5 phases were characterized by XRD and SEM. Aluminium based composites was fabricated by using the Al63Cu25Fe9Cr3 quasicrystalline particles as the reinforcing phase and ZL101 as matrix with mechanical stirring. The effects of quasicrystals content, on the microstructure and mechanical properties of the obtained composite, were investigated. The results show that the as-cast quasicrystalline material is composed of d-phase(Al65Cu20Fe10Cr5), I-phase(Al63Cu25Fe12), lambda-Al3Fe, beta-AlFe3 and a small amount of eta-AlCu, theta-Al2Cu phases. After heat treatment, the quasicrystalline intermediate alloy composition tends to quasicrystal phase. In the composite material, the diffusion between the quasicrystalline and the matrix alloy caused the decomposition of the structure of quasicrystalline phase. With the increase of quasicrystalline content, the tensile strength of the composites increases. However, addition of the Cr element changes the acicular beta-Fe(Al80-85Fe6-9Si10-15) phase into a manlike or bone-like alpha-Fe(Al80-85Fe4-8Si6-8Cr3-5) phase which increases the elongation of the composite. The best comprehensive mechanical properties corresponded to the 7 wt% quasicrystalline particles. Strengthening mechanism of quasicrystal reinforced aluminum matrix composites, a model that model considers the dislocation strengthening mechanism and the effect of load transfers mechanism on the tensile strength of composites. This theory calculates the tensile strength of quasicrystalline reinforced aluminum matrix composites and verifies the effectiveness of the model through experiments.

Structure and flaws of CuCr alloys by explosive compaction

Numerical investigation of fracture behavior of nanostructured Cu with bimodal grain size distribution

Study on the Relationship Between Compact Density and Compaction Energy of CuCr Alloys by Explosive Compaction

Structure and properties of the mechanically alloyed Cu-5Cr alloy

Characteristics of CuCr Contact Materials Made by Explosive Sintering

Microstructures and Mechanical Properties of (Alcocrfemn)(100-X)cu-x High-Entropy Alloys

Energy and Deformation During Explosive Compaction of CuCr Alloys

Eftect of third element on properties of CuCr alloys produced by explosive compaction

Characterization of Aluminium Matrix Compositesreinforced by Al–Cu–Fe-Cr Quasicrystalline Particles

Microstructure and Compressive Deformation Behavior of As-Cast CrFeCoNiCux High Entropy Alloys

The Microstructure and Mechanical Properties of High Entropy Alloy CoCrFeNiMn Matrix with Cr3C2 Reinforcement and Ag, BaF2/CaF2 Solid Lubrication

Probing the Respective Strengthening Mechanism of High-entropy (CoCrFeNi/CoCrFeNiMn) and Single-principle-element (Cu-4Al) Alloys

Compressive Fracture Behavior of Cu-Based Bulk Amorphous Alloys

Fabrication of High Strength Conductivity Submicron Crystalline Cu-5%Cr Alloy by Mechanical Alloying

Microstructure evolution, Cu segregation and tensile properties of CoCrFeNiCu high entropy alloy during directional solidification

Microstructure Characterization of the Cu-Ti-C Composites Prepared by Mechanical Alloying and Spark Plasma Sintering

Improving the Mechanical Performance of Cu Cr Alloy by Dissolving Cu in the Cr Second Phase

Structures, Properties and Responses to Heat Treatment of Deformation Processed Cu-15% Cr Composite Powders Prepared by Mechanical Milling

Microstructure and Properties of Rapid Solidified Cu_(71)Cr_(29) Alloy

Mechanical Alloying of the Immiscible Cu-60wt%Cr Alloy: Phase Transitions, Microstructure, and Thermodynamic Characteristics

Impact of Cu Content on Microstructural Evolution and Mechanical Behavior of CoCrMo0.5TiVCux High-Entropy Alloys