Abstract:Cu-3Ni-0.7Si-xCr-0.05Mg (x = 0.1 and 0.4) (wt% nominal composition) alloys were fabricated to investigate the effect of Cr contents on properties evolution and precipitation behavior of Cu-Ni-Si alloy. The results of the property analysis show that trace addition of 0.1 wt% Cr element contributes a better strength (ultimate tensile strength of 823 MPa) after single cold rolling and aging treatment. The precipitation behavior is characterized by transmission electron microscopy. It is found that nanoscale FCC structural Cr precipitates shift into submicron Cr 3 Si particles with Cr content increasing from 0.1 wt% to 0.4 wt%. Meanwhile, such superior formation of Cr 3 Si particle decreases the fraction of δ-Ni 2 Si owing to quick consumption of Si element from Cu matrix. Further quantitative analysis of various strengthening mechanisms reveals that the changed precipitation behavior notably affects their strengthening contribution to Cr contained alloys, resulting in an increase of more than 5.6% in the Orowan-Ashby mechanism. Surprisingly, in the case of the aging state at a temperature of 460 °C for a duration of 2 h, it is confirmed that although a much larger strengthening effect origins from nanosized δ-Ni 2 Si precipitate, the strength variation relies more on the Cr precipitation. That is, the lower strength at higher Cr content is mainly caused by the lower strengthening effect from Cr element related phases. In addition, the effect of the addition of trace Cr element on the operating mechanism on conductivity is also clarified. The results are expected to provide an appropriate content of Cr element and a dependable processing theory guidance for improving the comprehensive properties of the Cu-Ni-Si alloys.

Improving the Mechanical Performance of Cu Cr Alloy by Dissolving Cu in the Cr Second Phase

Improving the High Temperature Mechanical Performance of Cu-Cr Composite Induced by Residual Nano-Sized Cr Precipitates

Improving the High Temperature Mechanical Performance of Cu–Cr Alloy Induced by Residual Nano-Sized Cr Precipitates

Enhanced precipitation-hardening of Cu-Ag alloys through controlled chromium addition

Significantly enhanced high-temperature mechanical properties of Cu-Cr-Zn-Zr-Si alloy with stable second phases and grain boundaries

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Microstructure and Property Evolution of Cu–9Ni–6Sn-xCr Alloys During Thermo-Mechanical Treatment Process

Extension of Solid Solubility and Structural Evolution in Nano-Structured Cu-Cr Solid Solution Induced by High-Energy Milling.

Fe microalloying during the in-situ synthesis of homogeneous CuCrFe alloys by aluminothermic Self-propagating

Fabrication of High Strength Conductivity Submicron Crystalline Cu-5%Cr Alloy by Mechanical Alloying

Performance improvement of laser additive manufactured Cu‒Cr alloy via continuous extrusion

Structure and properties of the mechanically alloyed Cu-5Cr alloy

Tuning the microstructure and mechanical properties of magnetron sputtered Cu-Cr thin films: The optimal Cr addition

Enhanced mechanical properties and strengthening mechanism of Cu-Ni-Si alloy with trace chromium addition

Inclusion Removal Process of Homogeneous CuCr50 Alloy In-Situ Synthesized by Al-Mg Composite Strengthening Reduction Coupling Slagging

Design of Cu–Cr Alloys with High Strength and High Ductility Based on First-Principles Calculations

Effects of Cr addition on the constitutive equation and precipitated phases of copper alloy during hot deformation

Synergistic strengthening effects of precipitation and work hardening in cold-rolled Cu-0.4 wt%Cr alloy

Optimizing mechanical and electrical properties of Cu–3Zr alloy by thermomechanical processing

Improvement of Interfacial Bonding and Mechanical Properties of Cu-Al2o3 Composite by Cr-Nanoparticle-Induced Interfacial Modification

Mechanical Alloying of the Immiscible Cu-60wt%Cr Alloy: Phase Transitions, Microstructure, and Thermodynamic Characteristics