Abstract:Manufacturing CuCrZr alloy parts with high strength and high surface quality by selective laser melting (SLM) is a challenging task. This study investigates the microstructure, mechanical properties and machinability of SLM processed and heat-treated CuCrZr alloy through tensile test, compression test and ultra-precision machining. The microstructure analysis shows that the grain morphology and orientation are highly related to the laser track and building direction. Grain epitaxial growth is found on both horizontal (XY) and vertical (XZ) planes, which bends at the boundary of the molten track/pool. After heat treatment, molten track boundaries disappear and the slender and bent grains on the XY plane are replaced by polygonal square grains, but the large epitaxial grains on the XZ plane still remained. X-ray diffraction results indicate that the as-built sample contains α-Cu, Cr and CuxZry phases and building direction has an influence on the crystallographic orientation distribution. As-built (AB) CuCrZr alloy shows a comparable yield strength (218.0 MPa) with solution + ageing-treated (SAT) (231.3 MPa), which is much higher than that of the solution-treated (ST) counterpart (131.0 MPa). Although the ultimate tensile strength of the AB sample is lower than that of the SAT sample, its elongation at break (46.5%) is much higher than the latter (19.1%). The compressive strength of the AB sample is slightly lower than the SAT sample but higher than the ST sample. At low cutting speed, the ST sample shows a higher cutting force. High cutting speed will lead to the increase of cutting force of the AB and SAT samples but has a much lower effect on the ST sample. The XZ plane of the AB sample shows better machined surface quality. SAT sample has the highest material recovery during cutting and its chip will change from spiral to arc shape with the increase of cutting speed.

Performance improvement of laser additive manufactured Cu‒Cr alloy via continuous extrusion

Accelerating Discontinuous Precipitation to Increase Strength by Pre-Deformation in Cu-Ni-Si Alloys

Laser–Direct Current arc Hybrid Additive Manufacturing of Cu-Cr-Zr Alloy: Microstructure Evaluation and Mechanical Properties

Laser Cladding Fe/FeCr Coatings on Continuous Casting Cu Mold

Performance Improvement for the CuCrZr Alloy Produced by Laser Powder Bed Fusion Using the Remelting Process

Preparation of high strength and electrical conductivity copper-chromium pseudobinary alloy by cold-rolling of a billet produced by laser additive manufacturing

Microstructure and mechanical properties of Cu-Cr-Zr alloy prepared by electron beam additive manufacturing and laser-MIG hybrid welding

Laser additive manufacturing of Cu–Cr–Nb alloys by using elemental powder

Additively manufactured CuCrZr alloy: Microstructure, mechanical properties and machinability

Modification of Electrical and Mechanical Properties of Selective Laser‐Melted CuCr0.3 Alloy Using Carbon Nanoparticles

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

Preparation of Cu-Cr-Zr Alloy by Laser Powder Bed Fusion: Parameter Optimization, Microstructure, Mechanical and Thermal Properties for Microelectronic Applications

Selective laser melting of CuCrZr alloy: processing optimisation, microstructure and mechanical properties

Mechanical Properties and Interfacial Characterization of Additive-Manufactured CuZrCr/CoCrMo Multi-Metals Fabricated by Powder Bed Fusion Using Pulsed Wave Laser

Effect of heat treatments on microstructure, mechanical and electrical properties of Cu–Cr–Zr alloy manufactured by laser powder bed fusion

Introduction of nanoprecipitation into supersaturated CoCrFeNiMo0.5 alloy prepared by laser-powder bed fusion via microstructure tailoring to achieve excellent properties

The Influence of Heat Treatment on Microstructure and Properties of Selective Laser Melting CuCrZr Alloy

The significant impact of grain refiner on γ-TiAl intermetallic fabricated by laser-based additive manufacturing

Microstructure evolution and frictional wear behavior of Al‐18Si‐4Mg‐2Mn‐0.5Fe‐xCu alloys fabricated by laser additive manufacturing

Microstructural Evolution and Mechanical Properties of a Continuously Cast Al–Mg–Si–Cu Alloy Processed by Repetitive Continuous Extrusion Forming

The mechanical and functional behaviors of Mn–15 wt.%Cu alloy produced by selective laser melting