Abstract:This work presents the experimental results of narrow gap butt welding of steel plates with large thickness by using the Metal Active Gas (MAG) welding method.The typical defects are accompanied with this process such as the infusion in the side wall and the porosity due to the narrow gap which affect on the melting process. Thus, some publications noted the results of welding for the thickness up to 20−30 mm and the chamfer angle about 30° using GMAW/MIG, GTAW/TIG, SMAW and new development such as laser – arc hybrid, laser multi- pass technique, super -TIG welding etc. But the production requires the solution to save the costs by the reduction of time, labour and investment keeping the standard quality. That is the aim of this study. In order to improve the quality of weld joint and increase the productivity of the process, is it suggested to develop the innovative welding process, in which the welding voltage – Uw, the translational velocity of the tip – Vt, and rotational velocity of the tip – Vr, are changing. This helped to increase the thickness of steel plates up to 50 mm and the chamfer angle decreased at 15°, providing the satisfied quality of the weld. The micrography study serve as the preliminary proof of this hypothesis. The microstructures in 4 regions, such as the weld center zone, heat-affected zone (HAZ), parent metal region, and the boundary between the weld metal and the HAZ were examined. The microstructures of 13 positions from different experiments are investigated using the optical microscope (Axiovert 25).These experiments covered all specific points (node) locating accordingly to three layers from bottom to top of the weld joint . The findings proved the welding quality is similar in case of narrow gap but the chamfer angle is twice lower and the thickness is increased. The result of the study enhances the productivity due to saving the labour cost and the welding materials. It is recommended to consider the effect of other factors (such as cooling conditions, dwell time when the arc approaching the side walls) to optimize the weld quality. There is the huge volume of the heavy steel constructions with the thick steel construction and specific narrow gap in industry. The results of this study with the optimization and more deeper evaluation the influence of main parameters of welding process to eliminate the typical defects will be the valuable reco mmendation for the managers and engineers in the production of metallic constructions

Research progress of narrow gap gas metal arc welding

Research Status and Development Trend of Narrow-Gap TIG Welding

Research on the sidewall penetration mechanisms of cable-type welding wire narrow gap GMAW process

Application of Rotating Arc System to Horizontal Narrow Gap Welding

Stability of Double Wires Narrow-gap Gas Metal Arc Welding

Study on Arc Behavior and Weld Formation of Magnetically Controlled Narrow Gap TIG Welding

The evaluation on performance of narrow- gap welding thick steel plates under the influence of main welding parameters

Characteristics of welding and arc pressure in TIG narrow gap welding using novel magnetic arc oscillation

Procedure of twin-wire narrow gap MAG welding with one molten pool

Numerical simulation on molten pool behavior of narrow gap gas tungsten arc welding

A novel high efficiency narrow-gap laser welding technology of 120 mm high-strength steel

An Innovative Methodology in Narrow Gap GTAW for Alternating Magnetic Field with Synchronous Swing of Filler Wire and Arc

Numerical Simulation on the Nonaxisymmetry Arc Characteristics in Narrow Gap TIG Welding: Responses to Welding Parameters

Thick-wire swing arc narrow gap GMA welding assisted by pre-embedding cold wires

Comparison of Microstructure and Mechanical Properties of Ultra-Narrow Gap Metal Active Gas Arc Welded and Narrow Gap Submerged Arc Welded Q235A Low Carbon Steel

Feasibility study on tandem narrow gap GMAW of 65 mm thick steel plate

Correlation of Arc Sound and Arc-sidewall Position in Narrow Gap MAG Welding

Effects of Processing Parameters on Molten Behavior, Arc Stability, and Defect Forming in Swing-Arc Narrow Gap GMA Vertical Up Welding

Influence of Interwire Distance and Arc Length on Welding Process and Defect Formation Mechanism in Double-Wire Pulsed Narrow-Gap Gas Metal Arc Welding

Research on Design of Narrow Gap TIG Welding Torch

Study on Arc Characteristics and Their Influences on Weld Bead Geometry in Narrow Gap GMAW of 5083 Al-alloy