Abstract:Equal channel angular pressing (ECAP) is an efficient metal forming tool, generally used to improve the mechanical properties by refining the grain structure in metals and alloys. In the present work, both experimental and simulation approaches have been utilized to investigate the deformation behavior of EN AW 7075 alloy during ECAP. The formation and homogeneity of the Von-Mises stress and plastic strain of the samples during ECAP with different outer corner angles (OCAs) have been investigated by the finite element method (FEM). The results revealed that the effective strain was higher and uniform for 10°, 20°, and 30° OCAs die compared to other OCAs. Beyond 30°, the magnitude of strain was found lower with a less homogenous distribution of strain. A sharp plastic deformation zone (PDZ) was noticed for 10° and 20° OCAs, although broadened gradually over an OCA value of 20°. Moreover, lower and uniform Von-Mises stress was generated along the diameter of the sample for the OCA of 20° compared to other OCAs. A gradual reduction of plastic strain has been documented with the enhancement of OCAs along with the sample diameter. The sharpest damage, however, was noticed for the OCA of 90° due to the higher gap between the sample and both die surfaces. Interestingly, the most uniform severe plastic deformation and highest strain homogeneity in terms of inhomogeneity index and coefficient of variance were achieved for 20° and 30° OCAs. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analysis illustrated the formation of ultra-fine grain structures containing very fine η ́ and η precipitates during the post-ECAP process. An improvement in the hardness, yield strength, and ultimate strength by 22%, 18%, and 14%, respectively, after ECAP has been recorded in comparison to the initial artificially aged condition. The improvements in mechanical properties were improvised primarily due to grain refinement combined with precipitate hardening.

Deformation Behavior Analysis and Process Investigation of Equal Channel Angular Pressing

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Three-dimensional numerical analysis and experimental investigation of grain refinement in multi-pass equal channel angular pressing for round-workpieces

Ebsp Investigation of Microstructure and Texture Evolution During Equal Channel Angular Pressing of Aluminium

Severe plastic deformation of commercially pure aluminum using novel equal channel angular expansion extrusion with spherical cavity

Deformation mechanism finite element analysis and die geometry optimization of magnesium alloys by equal channel angular processing

Effect of equal channel angular extrusion process on deformation behaviors of Mg-3Al-Zn alloy

Investigating the Influence of Thermomechanical Equal Channel Angular Pressing (ECAP) Improved Die on AA-6061

Atomistic modeling of idealized equal channel angular pressing process

Mechanical responses, texture and microstructural evolution of high purity aluminum deformed by equal channel angular pressing

Grain Refinement and Strengthening of an Aluminum Alloy Subjected to Severe Plastic Deformation through Equal-Channel Angular Pressing

Microstructural evolution and mechanical properties of AZ31 Mg alloy fabricated by a novel bifurcation-equal channel angular pressing

Tailoring Deformation Homogeneity of WE43 Alloy through Strain Rate Sensitivity and Back Pressure during Equal Channel Angular Pressing

Influence of equal channel angular pressing in an acute angle die with a back pressure notch on grain refinement, torsion and mechanical properties of aluminium

1216 Nano-Scale Strength Analysis by EBSD and AFM Hybrid Method in Ultrafine-Grained Copper Processed by ECAP

Study on equal channel angular pressing process of Mg–Zn–Y–Mn–Ti magnesium alloy enhanced by lamellar LPSO phase and spherical W phase

Development of mechanical properties and microstructure for Al–Zn–Mg–Cu alloys through ECAP after optimizing the outer corner angles through FE modeling

Microstructure and mechanical properties of ultrafine grained IF steel processed by equal channel angular pressing

Study of strength-ductility and anisotropic behavior of Mg-Gd-Y-Zn-Zr alloy prepared by Equal channel double angular pressing

Orientation factor analysis of deformation mechanisms under special processing techniques in AZ31 magnesium alloys