Abstract:Zinc oxide (ZnO) varistors, which are produced by sintering ZnO powder together with small additives of Bi2O3, Co3O4, Sb2O3 and other oxides, are popular ceramic semiconductor devices and widely used in electric circuits and systems as voltage-clamping or surge-arrester owing to their extremely nonlinear current–voltage characteristics. The reliability of ZnO varistors is the most important consideration, and researches are mainly focus on the material properties of ZnO body and the effects of additives, such as ZnO grain size and the surrounding additive-rich insulating barriers. However, the manufacturing of electrodes still remains the traditional silver baking process, and few people investigate the effects of electrodes on the reliability of devices. In this paper, we propose a novel electrodes manufacture process using magnetron sputtering technology, and investigate the reliability of devices comparing to silver baking process. Two groups of samples with diameters of 20mm were prepared by silver baking and magnetron sputtering process respectively. The nonlinear voltage, nonlinear coefficient, and leakage current parameters were measured by the metal oxide varistor meter typed TTK-168; the energy absorption capacities were measured by a lightning current surge generator with 8/20μs impulse waves; the adhesive strength of electrodes was measured by a dynamometer; the microstructures of the samples were examined using Scanning Electron Microscope, and the change ratio of nonlinear voltages at an environment of 125°C after 100h was chosen as the main reliability parameter. Results show that the sputtered electrodes could improve the reliability of samples by reducing the change ratio from 1.32% to 0.61%, with other parameters exceeding the silver baking samples at the same time. This enhancement is benefit from the good interface between sputtered electrodes and ZnO substrate as well as the low temperature during magnetron sputtering process.

Preparation of High Potential Gradient ZnO-Based Thick-Film Varistors by High-Energy Ball Milling and Low-temperature Sintering

Study on the electrical properties and defect structures of a high voltage gradient ZnO varistor

High Voltage Gradient ZnO-Based Varistors from ZnO Nano-powders for DC Current Switching Application

Elaboration and electrical characterization of ZnO-based varistor ceramics in different sintering temperatures

Properties of ZnO Varistors Prepared with Nano-Sized Powders

Microstructure Design and Optimization of ZnO-Bi2O3-Sb2O3 Based Ceramic Varistors

Enhanced voltage gradient and energy absorption capability in ZnO varistor ceramics by using nano-sized ZnO powders

Microstructure and electrical properties of Pr 6 O 11 doped ZnO-Bi 2 O 3 -based varistors

Microstructure design and optimization of ZnO-Bi 2O 3-Sb 2O 3 based ceramic varistors

An ultralow concentration of Cr2O3 dopants driven lower temperature sintering ZnO‐based varistor ceramics

Effect of B2O3 doping on the microstructure and electrical properties of ZnO-based varistors

Effect of Fabrication Conditions on I–V Properties for ZnO Varistor with High Concentration Additives by Sol–gel Technique

Reliability enhancement of zinc oxide varistors using sputtered silver electrodes.

Optimization of Sintering Temperature and Doping Level of Cr2O3 in ZnO-Pr6O11-Based Varistor Ceramics

The Dependence of Sintering Temperature on Schottky Barrier and Bulk Electron Traps of ZnO Varistors

Microstructure and Electrical Properties of Ga2o3 Doping on Zno Varistor Ceramics with Different Sintering Temperature

Simultaneously Enhanced Potential Gradient and Nonlinearity of ZnO Varistor Ceramics by MnO Doping with Nano-Sized ZnO Powders

Admittance Spectroscopy of Y<sub>2</sub>O<sub>3</sub>-Doped ZnO Varistors Sintered at Different Temperature

High Voltage Zno Varistor Ceramics Doped With Sb2o3, Sio2 And Mgo

Effect of Sc2O3 doping on microstructure and electrical properties of ZnO–Bi2O3-based varistors