Abstract:Abstract Background Stress concentration may cause bone resorption even lead to the failure of implantation. This study was designed to investigate whether a certain sagittal root position could cause stress concentration around maxillary anterior custom-made root-analogue implants via three-dimensional finite element analysis. Methods The von Mises stresses in the bone around implants in different groups were compared by finite element analysis. Six models were constructed and divided into two groups through Geomagic Studio 2012 software. The smooth group included models of unthreaded custom-made implants in Class I, II or III sagittal root positions. The threaded group included models of reverse buttress-threaded implants in the three positions. The von Mises stress distributions and the range of the stresses under vertical and oblique loads of 100 N were analyzed through ANSYS 16.0 software. Results Stress concentrations around the labial lamella area were more prominent in the Class I position than in the Class II and Class III positions under oblique loading. Under vertical loading, the most obvious stress concentration areas were the labial lamella and palatal apical areas in the Class I and Class III positions, respectively. Stress was relatively distributed in the labial and palatal lamellae in the Class II position. The maximum von Mises stresses in the bone around the custom-made root-analogue implants in this study were lower than around traditional implants reported in the literature. The maximum von Mises stresses in this study were all less than 25 MPa in cortical bone and less than 6 MPa in cancellous bone. Additionally, compared to the smooth group, the threaded group showed lower von Mises stress concentration in the bone around the implants. Conclusions The sagittal root position affected the von Mises stress distribution around custom-made root-analogue implants. There was no certain sagittal root position that could cause excessive stress concentration around the custom-made root-analogue implants. Among the three sagittal root positions, the Class II position would be the most appropriate site for custom-made root-analogue implants.

[Analysis of the Movement of Long Axis and the Distribution of Principal Stress in Abutment Tooth Retained by Conical Telescope].

Analysis on the Stress of Abutment between the Uses of Two Telescope Crown Dentures to Restore Distal-extension Caused ;by Periodontal Disease

Three dimensional finite element analysis of biomechanical distribution of dental implants with immediate load and delayed load

Finite element analysis on stress distribution of mandibular alveolar mucosa under linear occlusal complete denture

Stress distribution in abutment teeth and related tissues under different design of connector: three-dimensional finite element analysis

The Effect of Different Abutment Designs and Materials on Stress Distribution in Implants and Peripheral Bones: A Three-Dimensional Finite Element Analysis

Influence of Different Abutment Designs on the Biomechanical Behavior of Dental Root-Analog Implant: A Three-Dimensional Finite Element Analysis

Influence of anisotropy on peri-implant stress and strain in complete mandible model from CT.

Effect Of Central Retainer Shape And Abduction Angle During Preparation Of Teeth On Dentin And Cement Layer Stress Distributions In Endocrown-Restored Mandibular Molars

Tooth movement tendency of space closure by sliding mechanics in customized lingual appliance: A 3-dimensional finite element analysis

Biomechanical Analysis of Rigid and Non-Rigid Connection with Implant Abutment Designs for Tooth-Implant Supported Prosthesis: A Finite Element Analysis

Effect of Implant-Abutment Connection and Abutment Angulations on Peri-implant Stress Levels: A Finite Element Analysis Study

Three-dimensional finite element analysis of effect of root canal taper and post on tooth stress distribution]

Effect of Angled Abutments in the Posterior Maxillary Region on Tilted Implants: a 3D Finite Element Analysis.

Three-dimensional Finite Element Stress Analysis of First Mandibular Premolar Restored by Different Materials under Loading

A comparative finite element analysis of titanium, poly-ether-etherketone, and zirconia abutment on stress distribution around maxillary anterior implants

Influence of Placement of Ultrashort Implant at Sub-Crestal, Crestal and Supra-Crestal Level with Titanium or Polyetheretherketone Hybrid Abutment: 3D Finite Element Analysis

[Two-Dimensional Finite Element Stress Analysis of Simulating Restored Teeth with Wedge-Shaped Defects under Loads].

Influence of sagittal root positions on the stress distribution around custom-made root-analogue implants: a three-dimensional finite element analysis

Biomechanical behaviour of tilted abutment after fixed partial denture restoration of CAD/CAM materials

Influence of clinic design of the prostheses with ERA attachment for distal extension defect: A three-dimensional finite dement analysis