Abstract:The effects of the powder size distribution on the hot deformation behavior and the microstructural differences of a novel nickel-based powder metallurgy superalloy (WZ-A3) were studied by SEM, EDS, EBSD, OM, and the thermal simulation testing machine. The results show that compared with HIP-01 sample made from fine powder, the dendrite structure of coarse powder is obvious and the composition segregation is serious. The residual primary gamma' of the HIP-02 sample made from the coarse powder is more than that of the HIP-01 sample. At the low temperature (1050, 1080 degrees C) and high strain rates (1, 0.1 s(-1)), the peak stress of HIP-01 sample is higher than that of HIP-02 sample. After hot compression, the crack situation at the edge of HIP-01 sample is more severe than that of HIP-02 sample. Most of the original microstructure of HIP-01 sample are retained, and the crack is generated at the prior particle boundary (PPB), while some recrystallized structure appears at the edge of HIP-02 sample. At 1080 degrees C/0.001 s(-1), the peak stress of HIP-02 sample is about 30 MPa lower than that of HIP-01 sample. The recrystallization phenomenon of HIP-02 sample during hot compression is obvious and the recrystallized grains are uniform. The HIP-01 has necklace crystal structure, and the recrystallization is not sufficient. The coarse gamma' can promote the recrystallization of HIP-02 sample at 1050 and 1080 degrees C. At high temperature (1150 degrees C) and low strain rates (0.001, 0.01 s(-1)), the gamma' dissolve into. matrix, and the thermal deformation behavior of the two samples is similar. No cracks occur in the samples, and the microstructure is fully recrystallized. The abnormal grown grains are found in the both samples at 1150 degrees C/0.001 s(-1).

Effect of Sulfur on Hot Ductility of Ni-Cr-W-Al Superalloy

Effect of Sulfur on the Hot Plasticity of GH625 Superalloy

Analysis of the Influence of Sulfur on the Hot Tensile Fracture of C71500 Cu-Ni Alloy

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Hot ductility behavior of medium carbon sulfur-containing alloy steel

Effect of trace sulfur on the hot corrosion resistance of Ni-base single crystal superalloy

Effect of Sulfur on Microstructures and Solidification Characteristics of a Nickel-Base Single Crystal Superalloy

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Effect of Carbon on the Microstructure and Stress Rupture Properties of a New Ni-Cr-W-Fe Alloy for Advanced Ultra-Supercritical Power Plants

Effect of Microstructure on High Temperature Mechanical Properties in Forming Ni-20cr-10mo-10co Superalloy

Effect of Sulfur on Antimony-Induced High-Temperature Ductility Deterioration of C-Mn Steel

Effects of Nitrogen Content on Microstructures and Tensile Properties of a New Ni–Fe Based Wrought Superalloy

The Effect of the Cooling Rates on the Microstructure and High-Temperature Mechanical Properties of a Nickel-Based Single Crystal Superalloy

Effect of Heat Treatment on the Microstructure and Fracture Behaviors of a Ni–Cr–Fe Superalloy

Effect of Carbon on the Microstructures and Stress Rupture Properties of a Polycrystalline Ni-Based Superalloy

Effect of loading direction on hot ductility of super austenitic stainless steel with columnar crystals

Effects of Heat Treatment on the Microstructure and Properties of a Cast Nickel-Based High-Cr Superalloy

The Effect of Sulfur on the Carburization of Three Fe–19Ni–21Cr– X Al ( X = 0, 2, 6 At.%) Alloys at 900 °C in Oxygen-Contaminated CH 4 –H 2 –H 2 S Atmospheres

Influence of Cr Content on Hot Corrosion and a Special Tube Sealing Test of Single Crystal Nickel Base Superalloy

Effects of alloying elements on the electronic structure and ductility of NiAl compounds investigated by X-ray absorption fine structure

Effect of the Powder Size Distribution on the Hot Deformation Behavior of a Novel Nickel-based Powder Metallurgy Superalloy