Abstract:Modern aero and power industry needs high-performance gas turbine. Directional solidification (DS) columnar grain and single crystal (SX) blade as key parts of gas turbine serve in heavy stress and high temperature conditions. The DS and SX blade are mainly produced by high rapid solidification (HRS) method, and HRS is one of useful DS technology, which has a property that the heat dissipating ways are changing during the process and the temperature gradients will vary correspondingly. The dendrite grain arrays were the substructure of a DS or SX blade. The structure of the dendrite grain arrays influences the mechanical property of the final casting very much, but is seriously affected by the solidification parameters, such as temperature gradient. In this work, the dendrite grain growth of DD6 superalloy was studied based on cellular automaton- finite difference (CA-FD) model concerning the HRS method's macro solidification parameters. Mathematic models for dendrite grain growth controlled by temperature field and solute field were built to describe the competitive growth and morphology evolution of dendrite grains. Then the dendrite calculation model was coupled with the models of DS process calculation, and some HRS solidification parameters were included, such as withdrawal rate, pouring temperature, etc. The coupled models were used to predict the dendrite grain competitive growth of DD6 superalloy during the DS process. The variation of solute distribution and the dynamic adjustment of dendritic spacing during the process could be predicted by simulating calculation. The DS experiment was carried out with a cylinder sample, and dendrite grains' distribution in the transverse and longitude section was observed by OM and SEM. Then the simulated dendritic morphology was compared with that by experiment. The primary and secondary dendritic spacing by experiment and simulation were measured, and the compared results revealed that as the DS process going on the temperature gradient decreased gradually and the primary dendritic spacing was increasing. So simulation results of the DS dendritic competitive growth were validated by the experiment results, and the proposed models could predict the dendrite grain morphology and the adjustments of DS dendritic spacing of DD6 superalloy very well.

Refined Dendrite and Precise Orientation of Nickel-Based Monocrystal Superalloy with Melt Superheating Treatment

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Influences of MCrAlY Coatings and TBCs on Oxidation Behavior of a Ni-Based Single Crystal Superalloy

Processing, Microstructures and Mechanical Properties of a Ni-Based Single Crystal Superalloy

Microstructural Evolution and Compositional Homogenization of a Low Re-bearing Ni-based Single Crystal Superalloy During Through Progression of Heat Treatment

Influence of directional solidification variables on the microstructure and crystal orientation of AM3 under high thermal gradient

Phase Field Simulation of Alloying Element Segregation During Solidification of DD5 Nickel-Base Single Crystal Superalloy

Effect of thickness on microstructure of thin-walled nickel-based single-crystal superalloy castings

Effect of secondary orientation on the microstructures in thin-walled castings of nickel-based single-crystal superalloys

Substrate stimulating technique for Ni-based single crystal superalloy preparation during direction solidification

Microstructure Development of Different Orientated Nickel-Base Single Crystal Superalloy in Directional Solidification

Development of Numerical Simulation in Nickel-Based Superalloy Turbine Blade Directional Solidification

Microstructure and Mechanical Property of a Directional Ni-Based Superalloy During Long-Term Exposure

Microstructure and Microsegregation in A Ni-Based Single Crystal Superalloy Directionally Solidified under High Thermal Gradient

Microstructures and homogenization behavior of a nickel-based superalloy used for 850¬Ý‚ÑÉ turbine disc prepared by electron beam smelting layered solidification

Orientation Control for Nickel-Based Single Crystal Superalloys: Grain Selection Method Assisted by Directional Columnar Grains

Experimental Study on the Micro-Mechanical Parameters of Ni-based Single-Crystal Superalloys Using Nanoindentation and Element Distribution Analysis

Numerical Simulation of Dendrite Grain Growth of Dd6 Superalloy During Directional Solidification Process

Dendrite evolution and quantitative characterization of γ′ precipitates in a powder metallurgy Ni-based superalloy by different cooling rates

Custom-designed heat treatment simultaneously resolves multiple challenges facing 3D-printed single-crystal superalloys

Microstructural Investigations of Ni-Based Superalloys by Directional Solidification Quenching Technique