Abstract:In this paper, Cu thin films were deposited on Si (100) substrates by the high-power impulse magnetron sputtering (HiIPMS) technique, and the effects of different duty cycles (from 2.25% to 5.25%) on the plasma discharge characteristics, microstructure, and electrical properties of Cu thin films were investigated. The results of the target current test show that the peak target current remains stable under 2.25% and 3% duty cycle conditions. Under the conditions of a 4.5% and 5.25% duty cycle, the target peak current shows a decreasing trend. The average power of the target shows a rising trend with the increase in the duty cycle, while the peak power of the target shows a decreasing trend with the increase in the duty cycle. The results of OES show that with the increase in the duty cycle, the total peak intensity of copper and argon emissions shows an overall increasing trend. The duty cycle from 3% to 4.5% change in copper and argon emission peak total intensity change is not obvious. The deposition rate and surface morphology of the copper film were investigated by scanning electron microscopy, and the deposition rate of the copper film increased with the increase in the duty cycle, which was mainly due to the increase in the average power. The surface roughness of the copper film was evaluated by atomic force microscopy. X-ray diffraction (XRD) was used to analyze the grain size and texture of the Cu film, and the results showed that the average grain size of the Cu film increased from 38 nm to 59 nm on the (111) and (200) crystal planes. Four-probe square resistance test copper film resistivity in 2.25%, 3% low duty cycle conditions of the copper film resistivity is generally higher than 4.5%, 5.25% high duty cycle conditions, the copper film resistivity shows the trend of change is mainly affected by the copper film grain size and the (111) face of the double effect of the optimal orientation. The lowest resistivity of the copper film measured under the 4.5% duty cycle condition is 1.7005 μΩ·cm, which is close to the intrinsic resistivity of the copper film of 1.67 μΩ·cm.

Effects of Pulse Parameters on Macro-Particle Production in Pulsed Cathodic Vacuum Arc Deposition

Effects of Pulsing Parameters on Production and Distribution of Macroparticles in Cathodic Vacuum Arc Deposition

Effects of Pulsing Frequencies on Macro-Particle Contamination During Pulsed Vacuum Arc Deposition

Surface morphology and crystal orientation of electrodeposited tungsten coatings with different pulse parameters

Effect of the Pulse Duty Cycle on the Microstructure and Properties of a Jet Electrodeposited Nanocrystalline Copper Coating

Investigation on Processing of Industrial Set-Up Plasma Enhanced Chemical Vapor Deposition with Pulsed D.C. Power

Effects of Electrode Negative Pulsing Ratio in Direct Energy Deposition via Variable-Polarity Cold Metal Transfer Process on the Deposition Behavior and Microstructural Characteristics

Effect of Burning Conditions on Erosion Shape of Cathode in Pulsed Cathodic Arcs

Effect of Pulse Electrical Parameters on Performance of Deposited Copper Coatings with Citrate System at Room Temperature

Enhanced Discharge and Surface Properties of TiSiCN Coatings Deposited by Pulse-Enhanced Vacuum Arc Evaporation

Microstructure control of ultra-high-strength AlZnMgCu alloys fabricated by wire arc directed energy deposition: the role of variable polarity electric pulse

Influence of Target Current on Structure and Performance of Cu Films Deposited by Oscillating Pulse Magnetron Sputtering

Effect of discharge pulsating on microarc oxidation coatings formed on Ti6Al4V alloy

Enhancement of Discharge and Deposition Rate in Dual-Pulse Pulsed Magnetron Sputtering: Effect of Ignition Pulse Width

Recent developments in pulsed magnetron sputtering

Effects of Pulse Duty Cycles on Microarc Oxidation Formed on Al

Effects of HiPIMS Duty Cycle on Plasma Discharge and the Properties of Cu Film

Effects of the Pulse Energy on the Characteristics of Ceramic Coatings on Titanium Alloys Prepared by Micro-arc Oxidation

Impact of Pulsed Laser Parameters and Scanning Pattern on the Properties of Thin-Walled Parts Manufactured Using Laser Metal Deposition

Improvement on uniformity of diamond-like carbon coatings inside metal tubes using high power pulse supply

A systematic study of pulse and pulse reverse plating on acid copper bath for decorative and functional applications