Abstract:Assorted morphologies of precipitates in fcc/bcc transformation systems have been reported, which often exhibit irrational characteristic. Various models have been developed to explain the habit plane (or the broad facet), but the overall morphologies of the precipitates are seldom explained quantitatively. In this work, the equilibrium cross-section of rod-shape austenite precipitates in duplex stainless steel is determined by atomistic simulation. The input orientation relationship (OR) between fcc and bcc phase is determined according to the O-line criterion (one of the interfaces contains a single set of dislocations), with the condition that the invariant line lies in close-packed plane pair of (1 (1) over bar(1) over bar)(f)|(10 (1) over bar)(b) and the Burgers vector of O-lines is [011](f|)/2|((1) over bar 11)(b)/2. The obtained OR is close to the K-S OR ((11 (1) over bar)(f)//(01 (1) over bar)(b), [101](f)//(111)(b)), with the deviation of 1.27 degrees from the parallelism in both planes and directions. Interfacial energy of interfaces in various orientations in the zone axis of the invariant line ([0.75 0.10 0.65](f)//[0.52 0.68 0.52](b)) has been calculated. To ensure the reliability of the calculated values, an initial atomic configuration free of interstitial and vacancy is constructed for each interface. The energies of the O-line interface, the interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) are found to have similar values, each at a local minimum. Based on the calculated interfacial energies, the equilibrium cross-section morphology is determined by the Wulff construction. The result shows that the morphology exhibits a near rhombus cross-section, which agrees consistently with experiments. One of the major facets is the O-line interface, normal to ((0.66) over bar 0.12 0.74)(f)//((0.51) over bar (0.24) over bar 0.83)(b), in agreement with the observation. The other facet is normal to Delta g((020)) (((0.25) over bar (0.87) over bar 0.42)(f)//(0.45 (0.73) over bar 0.51)(b)) in the calculated result, while it is normal to Delta g(((1) over bar 11)) (((0.36) over bar (0.77) over bar 0.53)(f)//(0.31 (0.71) over bar 0.63)(b)) in experimental results, with about 10 degrees difference between them. The discrepancy between calculated and observed results is probably because the experiments have not reached the equilibrium state. The dislocation structures in these three interfaces are identified from the atomic simulation results by a newly developed method based on the singular value decomposition of the Nye tensor. It confirms that the O-line interface contains a single set of [011](f)/2 dislocations with spacing of 1.5 nm. The interface normal to either Delta g(((1) over bar 11)) or Delta g((020)) contains two sets of dislocations. The dislocation structure in the facet normal to Delta g((1) over bar 11)) is in good agreement with experimental observation of the non-O-line facet, including the local decomposition of dislocation core to (1 (1) over bar(1) over bar)(f) stacking faults.

MEASUREMENT AND CHARACTERIZATION OF THE SURFACE RELIEF IN A DUPLEX STAINLESS STEEL

Measurement of deformed surface and key data processing based on reverse engineering

Determination of precise orientation relationships between surface precipitates and matrix in a duplex stainless steel

Quantitative Analysis for the Displacement of Tent-Shaped Surface Relief of Lath Martensite in Fe-Based Alloy

Measurement of Sub-Surface Microstructures Based on a Developed Ultrasonic Atomic Force Microscopy

A Feasible Surface Patterning Method for SEM-DIC: Achieving High-Resolution In Situ Mapping of Local Strain and Microstructure to Reveal the Effect of Slip Transfer on Shear Strain Near Grain Boundaries

Crystallography of Surface Precipitates in a Duplex Stainless Steel

An Extended Near-Coincidence-sites Method and the Interfacial Structure of Austenite Precipitates in a Duplex Stainless Steel

Rapid Measurement Of A High Step Microstructure With 90 Degrees Steep Sidewall

A TEM Study of the Crystallography of Austenite Precipitates in a Duplex Stainless Steel

Surface Patterning for Combined Digital Image Correlation and Electron Backscatter Diffraction In-Situ Deformation Experiments

An Investigation on the Equilibrium Morphology and Interfacial Structures of Pricipitates in Duplex Stainless Steel by Atomistic Simulation

Surface Relief Accompanying Martensitic Transitions in an Fe-Ni-C Alloy by Atomic-Force Microscopy and Phenomenological Theory of Martensitic Crystallography

Surface relief characteristics of martensitic transformation in a Fe-based shape memory alloy

Measuring Topographies from Conventional SEM Acquisitions.

AN IMPROVED KLEED/CMTA METHOD AND ITS APPLICATION ON Cu(001)1×1 SURFACE

Experimental Study of the Γ-Surface of Austenitic Stainless Steels

Characterization of the Terrace-Defect Interfaces Using in Situ Straining Techniques

Measurement and characterization of ultra-precision freeform surfaces using an intrinsic surface feature-based method

ATOMIC FORCE MICROSCOPE INVESTIGATION OF THE SURFACE RELIEF EFFECT OF BAINITE IN AN Fe-C-Mn-Ni-Si ALLOY

Surface Texture Characterization of Metal Selective Laser Melted Part With Varying Surface Inclinations