Abstract:Titanium matrix composites reinforced with ceramic particles are considered a promising engineering material due to their combination of high specific strength, low density, and high modulus. In this study, the TA15-based composites reinforced with a volume fraction of 10% to 25% (TiB+TiC) were prepared using powder metallurgy and casting technique. Microstructural characterization and phase constitution were examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). In addition, the microhardness, room temperature (RT) and high temperature (HT) tensile properties of the composites were evaluated. Results revealed that the reinforcements are distributed uniformly even in the composites with a high volume of TiB and TiC. However, as the volume fraction exceeds 15%, TiB and TiC particles become coarsening and exhibit rod-like and dendritic-like morphology. Microhardness increases gradually from 321.2 HV for the base alloy to a maximum of 473.3 HV as the reinforcement increases to 25vol.%. Tensile test results indicate that a reinforcement volume fraction above 20% is beneficial for enhancing tensile strength and yield strength at high temperatures, but it has an adverse effect on room temperature elongation. Conversely, if the reinforcement volume fraction is below 20%, it can improve high-temperature elongation when the temperature exceeds 600 °C.

In situ formation of nanometer size TiC reinforcements in Ti matrix composites

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

In situ (TiBw+TiCp)/Ti6Al4V composites with a network reinforcement distribution

Low Volume Fraction in Situ (ti5si3+ti2c)/ti Hybrid Composites with Network Microstructure Fabricated by Reaction Hot Pressing of Ti–SiC System

Nanostructured Diamond-Tic Composites with High Fracture Toughness

Microstructure and Wear-resistant Properties of in situ TiB-TiC Reinforced Titanium Matrix Composites by Laser Deposition Manufacturing

Oxidation behavior of in situ TiCp/Ti6Al4V composite with self-assembled network microstructure fabricated by reaction hot pressing

IN SITU TiBW/Ti COMPOSITES WITH A NOVEL QUASI- CONTINUOUS NETWORK REINFORCEMENT ARCHITECTURE

Microstructure of In-Situ Synthesized (tib+tic)/ti Composites Prepared by Hot-pressing

Microstructure, mechanical properties and strengthening mechanism of in-situ synthesized TiC/6061 nanocomposites

Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method

Processing, Microstructural Characterization and Mechanical Properties of in Situ Ti3AlC2/TiAl3 Composite by Hot Pressing

The microstructures of in-situ synthesized TiC by Ti-CNTs reaction in Cu melts

In-situ TiC/Ti composites based on Ti 2 AlC–Ti system: Reaction process, microstructure, and mechanical properties

Microstructural evolution, mechanical properties and wear behavior of in-situ TiC-reinforced Ti matrix composite coating by induction cladding

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Abrasive Wear and Physical Properties of In-Situ Nano-TiCx Reinforced Cu–Cr–Zr Composites

In-situ synthesis and superhigh modulus of network structured TiC/Ti composites based on diamond-Ti system

In-situ formed TiCx reinforced Ti composites derived from polyzirconocarbosilane precursor: Synthesis, characterization and mechanical properties

TiB2-TiC Ceramics Matrix Composites Prepared by in-situ Technique

High-performance Ti composites reinforced with in-situ TiC derived from pyrolysis of polycarbosilane