Abstract:Three-dimensional needle carbon fibre reinforced carbon and silicon carbide dual matrix composite (C/C-SiC) is one of a new type of high performance brake material. The carbon fibre preform prepared by three-dimensional needling method was first densified by chemical vapour infiltration (CVI) to form porous carbon/carbon (C/C) composites. Then, the porous C/C composites were converted into C/C-SiC by liquid silicon infiltration (LSI), in which silicon carbide matrix was formed by reaction of carbon and melting silicon. The microstructure, mechanical properties and friction behaviour of C/C-SiC have been investigated. The results indicated that the composite was composed of 55 wt% C, 39 wt% SiC and 6 wt% Si. The density of C/C-SiC was 2.2 g cm(-3) with 6.4% open porosity. The C/C-SiC exhibited good mechanical properties, especially excellent toughness which can help to avoid catastrophic brittle fracture. The flexural and compressive strength can reach to 214.6 MPa and 271.0 MPa, respectively. In addition, C/C-SiC had excellent impact damage tolerance of 25.2 kJ m(-2). Compared to the self-friction, the C/C-SiC with steel opposing material shown higher static coefficient of friction (0.74) and better stability coefficient (0.28), while exhibited lower dynamic coefficient of friction (0.25), higher temperature of friction subsurface (444 degrees C), higher wear rate (2.88 mu m cycle(-1)). The main wear mechanism of the C/C-SiC composites with different opposing material both includes adhesion and oxidation abrasion. (C) 2012 Elsevier Masson SAS. All rights reserved.

Structure and fracture mechanism of short fibre reinforced C/C-SiC composites

Microstructure and mechanical property of short fiber reinforced C/C-SiC composites

Mechanical properties of C/C-SiC composites by compression molding

Fracture behavior of multlayer SiC/C composites

Microstructure and mechanical properties of 2.5D curved shallow-crossing linking SiCf/SiC composites fabricated by chemical vapor infiltration

Effect of Fiber Dispersion on Compression Performance of C/C-SiC Composites

Effects of fiber dispersion on mechanical properties of C/C-SiC composites

Effects of preform structure on microstructure and mechanical properties of long/short fiber‐coupled C/C–SiC composites

Microstructures and mechanical properties of carbon fiber reinforced silicon nitride composites prepared by gel-casting

Microstructure and mechanical properties of 3D needled carbon fibre reinforced carbon and silicon carbide composites

Microstructure Evolution and Mechanical Properties of C/C-SiC Composites Prepared with Different Prefabricated Structures

Microstructure and Compressive Behaviour of 3D Needled C/SiC Composites

Microstructure and Mechanical Properties of SiCf/SiC Composite Prepared by Chemical Vapor Infiltration

Compressive Properties and Fracture Mechanism of C/C-SiC Composites Prepared by WC-ISR

Preparation and Tribological Properties of C Fibre Reinforced C/Sic Dual Matrix Composites Fabrication by Liquid Silicon Infiltration

Effect of Carbon Particle and Carbon Fiber on the Microstructure and Mechanical Properties of Short Fiber Reinforced Reaction Bonded Silicon Carbide Composite

Dynamic Compressive Fracture of C/SiC Composites at Different Temperatures: Microstructure and Mechanism

Effects of In-Situ Carbon Layer and Volume Fraction of SiC Fiber on the Mechanical Properties and Fracture Behaviors of SiCf/SiC Composites Fabricated by a Modified PIP Method

Behavior of Short Carbon Fibers in Cfiber/Si3N4 Composites by Hot Pressed Sintering

Microstructure Control of Highly Oriented Short Carbon Fibres in SiC Matrix Composites Fabricated by Direct Ink Writing

EFFECT OF C/C POROUS PREFORM ON THE MICROSTRUCTURE AND FLEXURAL STRENGTH OF C/C-SiC COMPOSITES