Abstract:The complex chemical structure of polypeptide and the imperfection of processing technology cause the mechanical properties of regenerated keratin to be hard and brittle. This defect seriously affects the application prospects of keratin materials. To solve the above problems, α-lipoic acid modified keratin (KER) was blended with Polyamide 6 (PA6) and prepared into composite fibers via the wet-spinning method in this work. The spinnability and spinning conditions of the KER/PA6 blend solution were analyzed by rheological theory. The results illustrated that keratin solution will easily form a gel state under certain temperatures and concentrations, which was not conducive to the preparation of regenerated fiber. When the temperature was 45 °C and the mass fraction was 10 %, the viscosity and rheology of the solution were appropriate. The rheological properties of the blend solution showed that too much keratin would make the solution easy to gel, which was not conducive to the preparation of regenerated fibers and may affect the fiber properties. On this basis, the prepared composite fibers were characterized to explore the macromolecular aggregation state of keratin and PA6 in fibers. FT-IR and XRD results proved that there was no chemical reaction between keratin and PA6 in the composite fibers, which belonged to physical blending. At the same time, the two polymers had good compatibility and can be blended at the molecular level. SEM, DSC, and tensile strength test results indicated that when the proportion of keratin was too high, the structure and properties of the composite fibers will have obvious defects, which was consistent with the rheological analysis. Therefore, the blend ratio of keratin/PA6 was determined to be 3:7. Under this condition, the fibers exhibited a homogeneous structure and good thermal properties, especially its mechanical properties were close to wool fibers. The KER/PA6 composite fibers show important research value and can also provide technical reference for the development of regenerated biomass materials.

Property Analyses of Coconut Charcoal Modified Polyester Fiber

Fabrication and properties of polypylene matrix composites reinforced by ultrafine bamboo-char

Composites of Polypropylene Reinforced with Ultrafine Bamboo-char: Morphology, Mechanical and Thermal Properties

Conversion from Bamboo Waste Derived Biochar to Cleaner Composites: Synergistic Effects of Aramid Fiber and Silica

Effect of Different Chemical Treatments on the Dispersion Properties of Carbon Fiber and Paper Properties

Study on Properties of Modified Bamboo Fiber Reinforced Polypropylene Composites

Thermomechanical Analyses of Alkali-Treated Coconut Husk-Bagasse Fiber-Calcium Carbonate Hybrid Composites

ANALYSIS OF COCONUT FIBER REINFORCED COMPOSITES WITH HOT PRESS TECHNIQUES

Production practice of 9.8tex cocoa charcoal modified polyester/cotton/Coolplus compact yarn

Study on structures and properties of isotropic pitches and carbon fibers from co-carbonization of aromatic-rich distillate oil and polyethylene glycol

The Study of Lycoell Bamboo Fiber Spinnability and the Development of Its Blended Yarn Products

Effect of organically modified montmorillonite clay on wear behavior of naturally woven coconut sheath/polyester composite

Investigation on the tensile and flexural behavior of coconut inflorescence fiber reinforced unsaturated polyester resin composites

Comparative study on physical properties of bio-based PA56 fibers and wearability of their fabrics

Enhancing spinnability and properties of carbon fibers through modification of isotropic coal tar pitch precursor

Characterization of the keratin/polyamide 6 composite fiber's structure and performance prepared by the optimized spinning process based on the rheological analysis

An Investigation on the Comprehensive Property Assessment and Future Directions of Single Bamboo Fiber Reinforced Polypropylene Composites Fabricated by a Non-Woven Paving and Advanced Molding Process

Investigation on Mechanical Properties of Bamboo and Coconut Fiber with Epoxy Hybrid Polymer Composite

Sodium carbonate treatment of fibres to improve mechanical and water absorption characteristics of short bamboo natural fibres reinforced polyester composite

Characterization and Application to Fiber Reinforced Composite of Catechol/polyethyleneimine Modified Polyester Fabrics by Mussel-inspiration

Preparation and Property of Carbon-Nanotubes/pet