Abstract:Microstructure, mechanical performance and wall thickness of long glass fiber‐reinforced polypropylene pipes formed via fluid‐assisted co‐injection molding. Fluid‐assisted co‐injection molding (FACIM) processes can be divided into water‐assisted co‐injection molding (WACIM) and gas‐assisted co‐injection molding (GACIM) processes. This study focuses on evaluating the quality of pipes formed through four distinct processes: water‐assisted co‐injection molding overflow (WACIM‐O), water‐assisted co‐injection molding short shot (WACIM‐S), gas‐assisted co‐injection molding overflow (GACIM‐O), and gas‐assisted co‐injection molding short shot (GACIM‐S). Wall thickness, wall thickness uniformity, fiber morphology, and pressure resistance were studied. Long glass fiber‐reinforced polypropylene was the outer layer while polypropylene was the inner layer. The total wall thickness of the four types of pipes tends to decrease along the flow direction; however, the total wall thickness of the short‐shot pipes increases at the end. The wall thickness uniformity of the GACIM pipes is better than that of the WACIM pipes while the average fiberglass fracture length of the FACIM‐O pipes is longer than that of the FACIM‐S pipes. Also, the average fiber fracture length of the WACIM‐O pipes is the longest. The fiber orientation distribution can be divided into the near‐mold wall layer, the outer core layer, and the near‐interface layer. The degree of fiber orientation increases layer by layer along the flow direction. Glass fiber orientation is the highest for the WACIM‐O pipes; the pressure resistance of FACIM‐O pipes is better than that of the FACIM‐S pipes. Highlights Pipes were successfully prepared from long glass fiber‐reinforced polypropylene and polypropylene as the material. The wall thickness uniformity of the fluid‐assisted co‐injection molding (FACIM)‐overflow pipes is satisfactory. The total wall thickness of the FACIM‐short shot pipes have notable variations. The water‐assisted co‐injection molding‐overflow pipes present a longer average fiber breaking length. The pressure resistance of FACIM‐overflow pipes is better than that of FACIM‐short shot pipes.

Foaming Structure Formed in Glass Fiber Reinforced PP Molded by Gas-assisted Injection Molding

Preparation of glass fiber reinforced phenolic injection molding materials and its properties

Study on the Flow, Foaming Characteristics and Structural Strength of Polypropylene Structural Foam Injection Molding by Innovative Nitrogen and Molten Plastic Mixing Mechanism

Direct In-Mold Impregnation of Glass Fiber Fabric by Polypropylene with Supercritical Nitrogen in Microcellular Injection Molding Process

Microcellular Injection Molding of Polypropylene and Glass Fiber Composites with Supercritical Nitrogen

Research on the quality of long glass fiber‐reinforced polypropylene pipes formed via fluid‐assisted co‐injection molding

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Effect of Gas Counter Pressure on the Surface Roughness, Morphology, and Tensile Strength between Microcellular and Conventional Injection-Molded PP Parts

COMPRESSION MOLDING OF POWDER IMPREGNATING LONG GLASS FIBER REINFORCED POLYPROPYLENE

Studies on Polypropylene/Carbon Fiber Composite Foams by Nozzle-Based Microcellular Injection Molding System

Microstructure and Properties of Microcellular Poly (phenylene Sulfide) Foams by Mucell Injection Molding

Foaming Behaviors of Polyetherimide/ Polypropylene-Graft-Maleic Anhydride Blends in the Microcellular Injection Molding Process

Numerical and experimental investigations on the mechanism of flow‐induced fiber orientation in short‐shot water‐assisted injection‐molded short‐glass‐fiber‐reinforced polypropylene

Structure and properties of glass fiber reinforced polypropylene compounds with high fluidity

Formation mechanism of high‐pressure water penetration induced fiber orientation in overflow water‐assisted injection molded short glass fiber‐reinforced polypropylene

The study of the chemical crosslinked and foamed PP/LDPE

Mechanical Properties of Injection Molded PP/PET-Nanofibril Composites and Foams

Effects Of Processing Conditions On Foaming Behaviors Of Polyetherimide (Pei) And Pei/Polypropylene Blends In Microcellular Injection Molding Process

Improvement of the dispersity of micro‐nano particles for PP/PVC composites using gas‐assisted dispersion in a controlled foaming process

Effect of gas on the polymer temperature in external gas-assisted injection molding

Preparation and characterization of microcellular injection molded foams from high-performance blends based on PPS-modified PPBESK