Abstract:Squeeze casting process can effectively resolve the casting difficulties for wrought aluminum alloys by pressurized solidification. The effects of applied pressure (0.1-125 MPa) on the microstructure refinement, non-equilibrium eutectic phase aggregation and fracture behavior of Al-Zn-Mg-Cu alloys prepared by squeeze casting were investigated through metallography, scanning electron microscopy and energy dispersive spectroscopy. The results showed that the primary α-Al grains transformed from coarse dendrites to refined equiaxed grains with increasing pressure. Considerable primary refinement was achieved at 100 MPa, with a significant decrease by 63% in the average grain size from 273 μm to 101 μm; the non-equilibrium eutectic phases were homogenized and refined, and almost dissolved into the Al matrix after T6 heat treatment. The mechanism of solidification behaviors in pressurized solidification was elucidated. Firstly, the applied pressure increased the thermodynamic driving force to promote primary grain nucleation. Secondly, the solute diffusion and constitutional undercooling at the front of the solid/liquid interface front were inhibited by pressure, and grain growth in a dendritic structure was thus restrained. Thirdly, interdependence theory and thermodynamic calculations were conducted to quantitatively describe the primary grain size changes under pressurized solidification. Lastly, the ternary eutectic reaction L → α-Al + T-Mg (Al, Zn, Cu) 2 + Al 2 Cu and binary eutectic reaction L→ α-Al + Al 7 Cu 2 Fe were suppressed by the reduced solute segregation. Furthermore, when the pressure increased from 0.1 MPa to 125 MPa, the ultimate tensile strength was raised from 428 MPa to 538 MPa, almost approaching that of samples by forging process. The refined eutectic phases decreased stress concentration and improved fracture behaviors.

Squeezing Casting AC4CH Alloy

Effect of squeeze pressure on the microstructure and mechanical property of Al-4Cu-1Mg alloy

Effect of Pressure on Microstructures and Mechanical Properties of Al-Cu-based Alloy Prepared by Squeeze Casting

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Effects of Squeeze Casting on Microstructure and Solute Distribution in Al-Cu Alloy

Experimental study of squeeze casting of ZK60 magnesium alloy

The Effects of Squeeze Casting on the Mechanical Properties and Microstructures of ZL201

Microstructure and Mechanical Properties of Al-5.0Cu-0.6Mn-0.5Fe Alloy Prepared by Squeeze Casting

Microstructure and Property of High Strength-ductility Al-5.0Cu-0.4Mn Alloys Prepared by Squeeze Casting

Production of Thin-walled Aluminum Alloy Shell by Squeezing Casting

Microstructure and Properties of Solution Heat-Treated Al-Si-Cu Alloy by Squeeze Casting

Effect of Pressure on Squeeze Cast Al-Cu-Mg Alloy

Effects of Rheo-Squeeze Casting Parameters on Microstructure and Mechanical Properties of AlCuMnTi Alloy

Effect of Si content on microstructures and mechanical properties of Al-5.0Cu-0.6Mn-0.7Fe alloy prepared by squeeze casting

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Squeeze Casting of Al-Cu Alloy

Effect of Cooling Rate on Microstructure and Mechanical Properties of Squeeze Cast Al–Cu–Mg Alloy

Effects of Processing Parameters on Squeezing Casting ADC12 Aluminum Alloy Connecting Rod's Cap

Microstructures and Mechanical Properties of In-Situ Al 3 Ti/2024 Aluminum Matrix Composites Fabricated by Ultrasonic Treatment and Subsequent Squeeze Casting

Squeezing Casting ADC12 Aluminum Alloy Connecting Rod

Effects of High Pressure on Fe-Rich Phases and Mechanical Properties of Al-14Si Alloys with Rheo-Squeeze Casting