Abstract:ZrO 2 ceramics are commonly known as 'hard and brittle' materials due to their exceptional properties, such as high hardness, heat resistance, chemical stability, and low thermal conductivity. However, the hole processing technique for ZrO 2 ceramics often results in significant tool wear and compromises the quality of the holes. This study investigates the removal mechanism of ZrO 2 ceramic materials by using carbide tools, diamond-coated carbide tools, and micro-sintered tools. It also analyzes the impact of processing parameters on the wear mechanism of different tools and the quality of hole processing in ZrO 2 ceramics. The findings revealed that at high spindle speed (8000 r/min) and low feed rate (1 mm/min), the diamond coating on the rake surface of the diamond-coated carbide tool tends to peel off, leading to the formation of sharp edges on the flank surface. This phenomenon results in a reduction in thrust forces. Moreover, it is observed that as the number of hole machining operations increases, the peeling of the diamond coating on the tool flank becomes more severe. The increase in feed rate causes the diamond coating peeling area on the rake face of the tool to expand toward the chisel edge and even reach the thinned edge area near the chisel edge. When the feed rate of carbide tools increases, the wear degree of the chisel edge gradually increases, while the wear degree of the main cutting edge corner position gradually decreases. At low spindle speeds, the main cutting edge breaks and the cutter head is also damaged and deformed. The main wear mechanisms of micro-sintered tools involve shedding, fragmentation, wear, and adhesion of diamond abrasive grains. The bottom surface of the tool tends to accumulate a significant amount of flaky adhesion, which dulls the tool and increases thrust force. In contrast to carbide tools, diamond-coated carbide tools offer improved hole exit quality. However, micro-sintered tools often exhibit large volumes of flaking at the hole exits, resulting in shell-like stripes on the peeled surface.

Research on Wear Behavior of Tools While Infeed Cutting Austempered Ductile Iron (ADI) with Ceramic Tools

Wear Behaviors of Pcd Tools in Turning Granite

Specific cutting force, tool wear and chip morphology characteristics during dry drilling of austempered ductile iron (ADI)

Cutting performance and wear mechanisms of PVD coated carbide tools during dry drilling of newly produced ADI

STUDY ON THE WEAR PERFORMANCES OF CERAMIC TOOLS FOR MACHINING 304 STAINLESS STEEL

Wear Behavior of Si3N4 Ceramic Cutting Tool Material Against Stainless Steel in Dry and Water-Lubricated Conditions

Cutting performance and wear characteristics of Si3N4‐SiCw‐HfB2 ceramic cutting tools in turning of ductile cast iron

Wear Mechanisms and Notch Formation of Whisker-Reinforced Alumina and Sialon Ceramic Tools during High-Speed Turning of Inconel 718

Drilling process of Cf/SiC ceramic matrix composites: Cutting force modeling, machining quality and PCD tool wear analysis

Wear Behavior of Ceramic Tools in Longitudinal‐Torsional Ultrasonic Vibration‐Assisted Milling

Tool wear mechanism of turning Inconel 718 and EEMD-based feature analysis

Milling with ceramic inserts of austempered ductile iron (ADI): process conditions and performance

The Effect of Cutting Speed and Depth of Cut on Surface Roughness During Machining of Austempered Ductile Iron

Research on Tool Wear in Machining of Particle Reinforced Aluminium Metal Matrix Composites Using PCD Tool

Experimental and numerical investigation of Inconel 718 machining with worn tools

Cutting performance and failure mechanisms of TiB2-TiC-Al2O3 multi-dimensional gradient ceramic tool in intermittent turning of hardened steel

Wear-resistant and Anti-adhesive Properties of WC-FeAl Cutting Tool on Dry Machining of Ductile Cast Iron

Influence of Austenite Stability on the Machinability of Different Grades of Austempered Ductile Iron (ADI) During Dry Turning Machining

Comparative study of tool wear mechanisms in drilling ZrO2 ceramics using various tool types

The impact of cutting speed and depth of cut on cutting force during turning of austempered ductile iron

Cutting performances and their failure mechanisms of ceramic tools for cutting stainless steel