Abstract:This study examined the hard turning of AISI D2 cold work tool steel subjected to deep cryogenic processing and tempering and investigated the effects on surface roughness and tool wear. In addition, the effects of the deep cryogenic processes on mechanical properties (macro and micro hardness) and microstructure were investigated. Three groups of test samples were evaluated: conventional heat treatment (CHT), deep cryogenic treatment (DCT-36) and deep cryogenic treatment with tempering (DCTT-36). The samples in the first group were subjected to only CHT to 62 HRc hardness. The second group (DCT-36) underwent processing for 36 h at −145 °C after conventional heat treatment. The latter group (DCTT-36) had been subjected to both conventional heat treatment and deep cryogenic treatment followed by 2 h of tempering at 200 °C. In the experiments, Al2O3 + TiC matrix-based untreated mixed alumina ceramic (AB30) and Al2O3 + TiC matrix-based TiN-coated ceramic (AB2010) cutting tools were used. The artificial intelligence method known as artificial neural networks (ANNs) was used to estimate the surface roughness based on cutting speed, cutting tool, workpiece, depth of cut and feed rate. For the artificial neural network modeling, the standard back-propagation algorithm was found to be the optimum choice for training the model. Three different cutting speeds (50, 100 and 150 m/min), three different feed rates (0.08, 0.16 and 0.24 mm/rev) and three different cutting depths (0.25, 0.50 and 0.75 mm) were selected. Tool wear experiments were carried out at a cutting speed of 150 m/min, a feed rate of 0.08 mm/rev and a cutting depth of 0.6 mm. As a result of the experiments, the best results for both surface roughness and tool wear were obtained with the DCTT-36 sample. When cutting tools were compared, the best results for surface roughness and tool wear were obtained with the coated ceramic tool (AB2010). The macroscopic and micro hardness values were highest for the DCT-36. From the microstructural point of view, the DCTT-36 sample showed the best results with homogeneous and thinner secondary carbide formations.

Cutting performance and failure mechanisms of TiB2-TiC-Al2O3 multi-dimensional gradient ceramic tool in intermittent turning of hardened steel

Performance and reliability of Al2O3/TiC ceramic tool with multi-bionic surface microstructure in intermittent dry turning of AISI 52100 hardened steel

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Experimental and Multiscale Numerical Investigation of Wear Mechanism and Cutting Performance of Polycrystalline Diamond Tools in Micro-End Milling of Titanium Alloy Ti-6Al-4V

The impact of mechanical properties on the cutting performance of Al2O3-based ceramic cutting tools for green turning of hardened steel

Cutting Performance and Tool Wear of SiAlON and TiC-whisker-reinforced Si3N4 Ceramic Tools in Side Milling Inconel 718

Molecular dynamics simulation of the effect of tool parameters on nano-cutting of polycrystalline γ-TiAl alloys

Mechanical properties and cutting performance of laminated graphene composite ceramic tools

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti–6Al–4V

A Study on the Development of a Composite Ceramic Tool ZrO2/(W, Ti)C and Its Cutting Performance

Cutting Performance and Wear Mechanism of Submicron and Ultrafine Ti(C, N)-based Cermets

An experimental and fem study on dry turning of rotor steel 26NiCrMoV145 using multilayer coated cemented carbide tool

Cutting Performance and Failure Mechanisms of a Pure WC Cutting Tool in Dry Cutting of Cr12Mn5Ni4Mo3Al Stainless Steels and HT200 Grey Cast Iron

Cutting performances and their failure mechanisms of ceramic tools for cutting stainless steel

Optimized Design of Structural Parameters of Si3N4-based Ceramic Tools with Variable Cross-Section

Wear mechanism of diamond-cutting tool in nano-cutting polycrystalline γ-TiAl alloy based on molecular dynamics simulation

Three-dimensional modeling of grain structure growth within ceramic tool material

Optimization of sintering parameters for fabrication of Al2O3/TiN/TiC micro-nano-composite ceramic tool material based on microstructure evolution simulation

Cutting Responses of Additive Manufactured Ti6Al4V with Solid Ceramic Tool under Dry High-Speed Milling Processes

Effect of machinability, microstructure and hardness of deep cryogenic treatment in hard turning of AISI D2 steel with ceramic cutting

Application of ceramic nanoparticles in microstructure manipulation and simultaneously strengthening toughness and wear resistance of tool and die steels