Abstract:Some h-p finite element computations have been carried out to obtain solutions for fully developed laminar flows in curved pipes with curvature ratios from 0.001 to 0.5. An Oldroyd-3-constant model is used to represent the viscoelastic fluid, which includes the upper-convected Maxwell (UCM) model and the Oldroyd-B model as special cases. With this model we can examine separately the effects of the fluid inertia, and the first and second normal-stress differences. From analysis of the global torque and force balances, three criteria are proposed for this problem to estimate the errors in the computations. Moreover, the finite element solutions are accurately confirmed by the perturbation solutions of Robertson & Muller (1996) in the cases of small Reynolds/Deborah numbers.Our numerical solutions and an order-of-magnitude analysis of the governing equations elucidate the mechanism of the secondary flow in the absence of second normal-stress difference. For Newtonian flow, the pressure gradient near the wall region is the driving force for the secondary flow; for creeping viscoelastic flow, the combination of large axial normal stress with streamline curvature, the so-called hoop stress near the wall, promotes a secondary flow in the same direction as the inertial secondary flow, despite the adverse pressure gradient there; in the case of inertial viscoelastic flow, both the larger axial normal stress and the smaller inertia near the wall promote the secondary flow.For both Newtonian and viscoelastic fluids the secondary volumetric fluxes per unit of work consumption and per unit of axial volumetric flux first increase then decrease as the Reynolds/Deborah number increases; this behaviour should be of interest in engineering applications.Typical negative values of second normal-stress difference can drastically suppress the secondary flow and in the case of small curvature ratios, make the flow approximate the corresponding Poiseuille flow in a straight pipe. The viscoelasticity of Oldroyd-B fluid causes drag enhancement compared to Newtonian flow. Adding a typical negative second normal-stress difference produces large drag reductions for a small curvature ratio δ = 0.01; however, for a large curvature ratio δ = 0.2, although the secondary flows are also drastically attenuated by the second normal-stress difference, the flow resistance remains considerably higher than in Newtonian flow.It was observed that for the UCM and Oldroyd-B models, the limiting Deborah numbers met in our steady solution calculations obey the same scaling criterion as proposed by McKinley et al. (1996) for elastic instabilities; we present an intriguing problem on the relation between the Newton iteration for steady solutions and the linear stability analyses.

EFFECTS OF VISCOSITY ON EQUATION OF MOTION AND CRITICAL FLOW VELOCITY OF FLUID-CONVEYING PIPE

Effects of Nondimensional Distance Between Two Square Cylinders on the Dissipation Characteristics of the Complex Flow

Viscoelastic flow in rotating curved pipes

Numerical simulation of 3-D turbulent flows in a cut-off valve and analysis of flow characteristics in pipe

Equation of Motion for Vibrating Pipes with Laminar and Turbulent Flow Profiles

Semi-analytical Solution for Dynamic Behavior of a Fluid-Conveying Pipe with Different Boundary Conditions

Numerical Analysis on Unsteady Intermittent Flow in a Rotating Curved Pipe

Fluid Flow and Mixed Convection Heat Transfer in a Rotating Curved Pipe

Unsteady intermittent flow in a rotating curved pipe

VIBRATION AND STABILITY OF PIPES CONVEYING FLUID WITH DISTRIBUTED FOLLOWER FORCE

Flow structure and combined free and forced convective heat transfer in rotating curved pipe

Effect of visco-plastic and shear-thickening/thinning characteristics on non-Newtonian flow through a pipe bend

Theoretical and experimental study on dynamic characteristics of L-shaped fluid-conveying pipes

New equation of turbulent fibre suspensions and its solution and application to the pipe flow

NUMERICAL ANALYSIS OF THE FLUID FLOW IN A ROTATING CURVED ELLIPTICAL PIPE

Numerical Simulation of Laminar Flow in Various Curved Pipes Using a Boundary-Fitted Coordinate System.

Effect of Non-Spherical Particles on the Fluid Turbulence in A Particulate Pipe Flow

Simple variational criterion for turbulent flow in pipe

Fully Developed Viscous and Viscoelastic Flows in Curved Pipes

APPLICATION OF DIFFERENT TURBULENT MODELS IN CALCULATION OF FLOW RESISTANCE IN PIPELINES AND COMPARISON THEREOF

Effect of Heat on Velocity and Heat Transfer Coefficient of the Fluid in a Pipe with a Laminar Flow