Abstract:The transformation-assisted consolidation under pressure has been demonstrated to be a promising method to fabricate the nano or submicron polycrystalline ceramic materials. The high pressure suppresses the long-range diffusion of the atoms and, consequently, restrains the grain coarsening. The new phases produced at high pressure could show finer grains under the appropriate thermodynamic conditions, which are not subject to the grain size of the raw materials. Ceramic materials exhibit the existence of the transformations under certain thermodynamic conditions and the formation of new phases generally undergoes the nucleation and growth. In the present work, monoclinic microcrystal ZrO2 with average grain size of 2 µm and Y2O3 with average grain size of 50 nm were mixed in molar ratio of 97∶3. The preparation of the samples was carried out by sintering at 5.5 GPa and temperatures of 800–1700 °C using the high pressure cubic cell, and the sample characterization was performed via the X-ray diffraction, scanning electron microscope and transmission electron microscopy. It was found that the monoclinic and submicron tetragonal composite polycrystalline ZrO2 in bulk is obtained under high pressure and high temperature. The average grain size of tetragonal ZrO2 fabricated at 1200, 1400, 1600 and 1700 °C is (145±62) nm, (246±165) nm, (183±62) nm and (245±107) nm, respectively. The synthesis of the fine-grained polycrystalline materials by the transformation under high pressure can solve the problems of agglomeration, adsorption and grain coarsening caused by the nanopowders as the starting materials in the conventional approach, which would be an alternative route to fabricate the fine-grained polycrystalline materials with the enhanced performances.

Bulk Nanocrystalline Zinc Solidified by High Pressure Methods

Fabrication of Submicron Tetragonal Polycrystalline ZrO2 by the Transformation of Micro Monoclinic ZrO2 under High Pressure

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Plastic Deformation of Nanocrystalline Zinc Investigated by Positron Annihilation Lifetime Spectroscopy

Bulk Nanostructure Formation Directly From The Multicomponent Alloy Melt

Nanocrystallization of Pure Zr Via Room Temperature Rolling Deformation

A Single‐Step Process to Produce Carbon Nanotube‐Zinc Compound Hybrid Materials

Crystallization of Zr41Ti14Cu12.5Ni10Be22.5 Bulk Metallic Glass under High Pressure Examined by in Situ Synchrotron Radiation X-Ray Diffraction

Amorphous Intergranular Films Enable the Creation of Bulk Nanocrystalline Cu-Zr with Full Density

Synthesis of Zinc Nanoparticles by the Gas Condensation Method in a Non-Contact Crucible and Their Physical–Chemical Characterization

Sintering of Nanocrystalline ZrO_2(3Y) by Hot-Pressing

Solid State Reaction of Mg with Ni under High Pressure

Densification and Phase Transformation During Pressureless Sintering of Nanocrystalline ZrO2–Y2O3–CuO Ternary System

Pressure-jump induced rapid solidification of melt: a method of preparing amorphous materials

Sintering of Nanocrystalline ZrO2(3Y) by Hot-Pressing

Pressure Effect on Crystallization of Zr41ti14cu12.5ni10be22.5 Bulk Metallic Glass Prepared by Shock-Wave Quenching

Structural stability and compressibility study for ZnO nanobelts under high pressure

Refinement and strengthening mechanism of Mg−Zn−Cu−Zr−Ca alloy solidified under extremely high pressure

Nanocrystalline Grain Structures Developed in Commercial Purity Cu by Low-Temperature Cold Rolling

Formation of nanocrystalline Fe73.5Cu1Nb3Si13.5B9 alloy under high pressure

Structural stability in nanocrystalline ZnO