Abstract:Designing a solid-state battery is a balancing act. Fast charging rates and high capacity are preferable, but safety and long battery lifetimes must also be preserved. When making a solid-state electrolyte, amorphous materials with greater lithium content are ideal—they have greater conductivity than their lower-lithium-content counterparts. In addition to high lithium content, recent studies have focused on eliminating grain boundaries in solid state electrolytes. Eliminating grain boundaries allows for safer charging and discharging by reducing the chances of dendrite formation and subsequent shorting. Through experiments, we tried to reconcile amorphous character and relatively higher lithium content to produce a mechanically robust, conductive electrolyte material that lasts over many cycles. We first coarsened Li 3 BO 3 powder in a tube furnace, then pelletized the powder at 253,411 bar via hydraulic press. The rapid joule heating method involves two carbon papers connected in parallel with a DC power supply. Using this configuration, we had access to rapid quenching rates that typically require expensive technology. Resistance from the carbon paper resulted in a rapid temperature increase proportional to the applied current so the carbon paper acted as a heating element. The Li 3 BO 3 pellet was inserted between the two papers where it heated to its melting temperature (760-880°C) within 20 sec. We hypothesized that shorter ramping and cooling times introduced by rapid joule heating would promote amorphous character in Li 3 BO 3 , compared to samples prepared in a tube furnace with longer heating and cooling times. Full width at half maximum values calculated from X-ray diffraction results for each sample suggest the samples prepared using rapid joule heating formed smaller crystalline domains than those manufactured in the tube furnace. Scanning electron microscopy images taken at 5.0k magnification confirm this calculation. Large grains can be seen in the traditionally heated sample whereas no grains are observable in the rapid joule heated sample. Smaller crystalline domains emphasize the effects of rapid cooling and encourage future studies in escalating heating and cooling rates to produce amorphous or partially amorphous electrolytes.

Pressure-jump induced rapid solidification of melt: a method of preparing amorphous materials

A Rapid-Quench Technique for Multi-Anvil High-Pressure-temperature Experiments.

Rapid Compression Induced Solidification of Two Amorphous Phases of Poly(ethylene Terephthalate)

A Simplified Rapid-Quench Multi-Anvil Technique.

Rapid-quenching of High-Pressure Depolymerized Hydrous Silicate (peridotitic) Glasses

Ultrafast Crystallization Mechanism of Amorphous Ge15Sb85 Unraveled by Pressure-Driven Simulations

Pressure-dependent Microstructure Evolution of Fe-based Amorphous Alloy Powders Via High-Pressure Gas Atomization

A novel rapid cooling assembly design in a high-pressure cubic press apparatus

Rapid Viscous Flow of the Supercooled Liquid of Zr-Based Bulk Amorphous Alloy

Effects of pressure on microstructure evolution of liquid Fe-S-Bi alloy during rapid solidification: A molecular dynamics study

Exothermic Supercooled Liquid?Liquid Transition in Amorphous Sulfur

Rapid Joule Heating Method Applied to Solid State Electrolyte Materials

Synthesis of Highly Amorphous Fe 70 Ti 2 Y 6 B 22 Bulk Alloy with Excellent Thermal Stability by Isothermal Compression under High Pressure

Microscopic mechanisms of pressure-induced amorphous-amorphous transitions and crystallisation in silicon

Pressure-induced Amorphization of Crystalline Silica

Structural Transition in Amorphous Sulfur Compressed Up to 100 Gpa

Direct Single Crystal to Amorphous Transformation and Memory Effect in AlPO 4 -17

Nanostructure Evolution of Isotropic High-Pressure Injection-Molded Uhmwpe During Heating

Bulk Nanocrystalline Zinc Solidified by High Pressure Methods

Pressure-Induced Amorphous-To-Amorphous Reversible Transformation in Pr75al25

Flow and Pressure Jointly Induced Ultrahigh Melting Temperature Spherulites with Oriented Thick Lamellae in Isotactic Polypropylene