Analysis of DC Offset Calibration Techniques for Direct-Conversion Receivers

唐琴,吴建辉

IF: 1.992

2008-01-01

Microelectronics Journal

Abstract:Several DC offset calibration(DCC)techniques were described.Advantages and disadvantages of different techniques were analyzed and discussed.Emphasis was made on the development of negative DC feedback technique to reduce DC offset.Finally,potential applications of DCC techniques were summarized.

What problem does this paper attempt to address?

An Effective DC Offset Calibration Method Combined with Analog and Digital Circuits for Direct Conversion Receivers

Fengjie Wang,Liyi Fan,Yupeng Shen,Hua Chen,Jiarui Liu,Zhiyu Wang,Faxin Yu

DOI: https://doi.org/10.1587/elex.16.20190518

2019-01-01

IEICE Electronics Express

Abstract:This paper presents a DC offset calibration (DCOC) method combined with analog and digital circuits for direct conversion receivers. To work effectively, the LNA is shut off for better isolation and replaced by an equivalent resistance to keep the same transfer function of DC offset between calibration and operation. This method adopts DACs to compensate DC offset, then averages and eliminates the residual DC offset in the digital domain. Measurements show that this DCOC method achieves 0.44 mV DC offset and improves IM2 by 10 dB. The DCOC circuits occupy 0.23 mm(2) in 40 nm CMOS and consume 124 mu A at 1.3 V supply.
High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

Yiming Han,Fengjie Wang,Jiarui Liu,Zhiyu Wang,Faxin Yu

DOI: https://doi.org/10.3390/electronics10161966

IF: 2.9

2021-01-01

Electronics

Abstract:To improve the linearity of direct conversion receivers (DCRs), two high-linearity methods for high second-order intercept points (IP2s) and high third-order intercept points (IP3s) are proposed. To improve IP3s, a transconductance equalization technique for a complementary input operational amplifier (OPAMP) is proposed in an active-RC low-pass filter (LPF), while a digital-analog hybrid DC offset calibration (DCOC) method is proposed to improve IP2s. For one thing, the proposed transconductance equalization technique employs a pair of resistors to guarantee high voltage gain for an OPAMP with two-stage Miller topology under a high-input voltage swing to improve linearity with little deterioration of the noise performance. For another, during the DCOC method, the low-noise amplifier is turned off and replaced by an equivalent resistance of the output impedance of the low-noise amplifier to ensure the accuracy and effectiveness of the DCOC method. Fabricated in 40-nm CMOS technology, the receiver with proposed methods can realize a noise figure of 2.6–3.5 dB in the full frequency band, with an OIP3 of 28 dBm, an IM2 more than 70 dBc, and a remaining DC of −53.2 dBm under the total voltage gain of 60 dB.
A Frequency-Domain I/Q Imbalance Calibration Algorithm for Wideband Direct Conversion Receivers Using Low-Cost Compensator.

Xiaoye Peng,Faxin Yu,Zhiyu Wang,Jiarui Liu,Chenge Wang,Jing Wang

DOI: https://doi.org/10.1109/access.2023.3276715

IF: 3.9

2023-01-01

IEEE Access

Abstract:The amplitude and phase imbalances of the in-phase (I) and quadrature (Q) branches inherent in the direct conversion receiver structure cause the generation of image frequency interference signals. In this paper, a frequency-domain I/Q imbalance calibration algorithm is proposed for wideband direct conversion receivers. The I/Q imbalance model is rebuilt by applying the infinitesimal method and FFT algorithm. The mathematical expressions for the exact computation of the I/Q imbalance parameters are derived based on the frequency-domain statistical properties of the baseband signal. The two phase parameters, frequency-dependent I/Q imbalance (FD-IQI) and frequency-independent I/Q imbalance (FI-IQI), are separated according to the parity properties of the imbalance parameter. To avoid the interference from the transmitter, the receiver impairment estimation is performed using a frequency offset (FO) DC training signal, and a low-cost real-valued compensation (RVC) filter is introduced to correct the impairments of the received signal. The performances of the proposed calibration model are evaluated through simulations and experiments. The simulation results show that the image rejection ratio (IRR) is improved to 80-120 dBc and can also exceed 40 dBc at high noise levels. The experimental results based on the CX9261A evaluation board show that the average IRR of the multi-tone signal is increased by 24.99 dB, and the IRR of the wideband signal is increased by 19.08 dB.
A DC Offset Cancellation Circuit Using Digital Assistance Technique and Self-Calibrating Comparator for RF Transceiver

Zhiyuan Cao,Chengcheng Zhang,Zirui Jin,Dongsheng Liu

DOI: https://doi.org/10.1109/asicon58565.2023.10396145

2023-01-01

Abstract:This paper describes a dc offset cancellation (DCOC) circuit using digital assistance technique. This DCOC includes a self-calibrating comparator, a counter, and a 8-bit binary weighted current DAC. It is used in amplifiers for RF transceivers. The DCOC in this paper calibrates the offset by injecting current into the resistor of the amplifier. This method does not cause damage to the desired signal. It also avoids the use of large capacitors and resistors, with an area of 0.004mm 2 and power consumption of 12.1μW. With the self-calibration, the comparator has an input offset of less than 505μV. The Monte Carlo simulation shows that the 3σ value of the output residual offset of the amplifier is 1.64mV.
A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

Yiping Feng,Gaku Takemura,Shunji Kawaguchi,Nobuyuki Itoh,Peter R. Kinget

DOI: https://doi.org/10.1109/isscc.2010.5434044

2010-01-01

Abstract:Direct conversion receivers offer a high level of integration for multiband applications. For standards operating in full duplex, like WCDMA, a very high IIP2 is needed due to transmit signal leakage. Several circuit, compensation and calibration techniques to improve the IIP2 have been developed, but they usually result in a trade-off between IIP2, area, power and other specifications [1,2]. The IIP2 is very sensitive to manufacturing variations and operating conditions such as supply voltage, LO power or frequency, and temperature. We present a robust automatic background self-calibration technique with minimal overhead and performance penalties on the receiver front-end or baseband due to its digital implementation (Fig. 3.8.1). Such digital IIP2 calibration is also free of mismatch. The 0.13µm 1.8GHz CMOS RF front-end without external filter between LNA and mixer has an IIP2 better than 60dBm-sufficient for WCDMA applications [3]- with a state-of-the-art noise figure and power consumption.
Digitally Assisted IIP2 Calibration for CMOS Direct-Conversion Receivers

Yiping Feng,Gaku Takemura,Shunji Kawaguchi,Nobuyuki Itoh,Peter R. Kinget

DOI: https://doi.org/10.1109/jssc.2011.2161213

IF: 5.4

2011-01-01

IEEE Journal of Solid-State Circuits

Abstract:A robust digitally assisted self-calibration technique is presented to improve the input-referred second-order-intermodulation intercept point (IIP2) of direct-conversion receivers. The low-power, low-noise 1.8-GHz CMOS receiver prototype relies on digital signal processing to improve analog/RF performance with only a minimum hardware overhead and with no performance penalties on the RF front end and analog baseband. The RF front end achieves an IIP2 better than 60 dBm without external filters between the LNA and downconversion mixers, has a conversion gain of 38.5 dB, a low DSB noise figure of 2.6 dB, and an IIP3 of -17.6 dBm. It consumes 15 mA from a 1.5-V supply, and occupies 1.56 mm2 on a 0.13-μm CMOS process.
A LUT-free DC Offset Calibration Method for Removing the PGA-gain-correlated Offset Residue.

Lingwei Zhang,Hanjun Jiang,Fule Li,Jingjing Dong,Zhihua Wang

DOI: https://doi.org/10.1016/j.aeue.2012.12.010

IF: 3.169

2013-01-01

AEU - International Journal of Electronics and Communications

Abstract:This paper presents a novel DC offset calibration method for the zero-IF (intermediate frequency) receiver that removes the PGA-gain-correlated offset residue. The conventional calibration method is usually based on the classic input/output referred offset model, in which the receiver IF programmable gain amplifiers (PGAs) have offset sources that varies a lot with different gain settings. Consequently, the conventional calibration method needs to generate the calibration code at each gain step and requires a huge look up table (LUT) to store the calibration values. This paper presents a new DC offset model which is gain non-correlated, by analyzing two types of commonly-used PGA. Based on the new model, a LUT-free single-step DC offset calibration method in together with the implementation circuit is designed. The proposed method has been verified on a practical zero-IF receiver circuit in a standard 0.18 μm CMOS technology through the Monte Carlo (MC) simulation. The simulation results show that the receiver IF output offset residue after calibration using the proposed method is reduced to below 12 mV, which is comparable to the LUT-based conventional calibration.
A Low-Power DC Offset Calibration Method Independent of IF Gain for Zero-if Receiver.

JingJing Dong,HanJun Jiang,LingWei Zhang,JianJun Wei,FuLe Li,Chun Zhang,ZhiHua Wang

DOI: https://doi.org/10.1007/s11432-014-5170-0

2014-01-01

Science China Information Sciences

Abstract:A novel low-power DC offset calibration (DCOC) method independent of intermediate frequency (IF) gain for zero-IF receiver applications has been reported. The conventional analog DCOC method consumes greater power and affects the performance of the receiver. The conventional mixed-signal method requires enhanced memory to store the calibration results at different receiver gains as the DC offset is relative to the radio frequency (RF) and IF gain. A novel algorithm is presented to make the DCOC process independent of IF gain, which significantly reduces the memory area. With the proposed circuit, the receiver calibrates only once so settle-time and power consumption of the IF circuit is lowered. A DCOC circuit with the proposed method is manufactured in 0.18 μm CMOS technology that drains nearly 0 mA equivalent current from a 1.8 V power supply.
A Simple DC-Offset Eliminating Method of the Series-Inductance Current for the DAB DC–DC Converter

Nie Hou,Jingxin Hu,Di Mou,Yue Zhang,Yun Wei Li,Rik W. De Doncker

DOI: https://doi.org/10.1109/tpel.2022.3231816

IF: 5.967

2023-02-18

IEEE Transactions on Power Electronics

Abstract:Based on the phase-shift modulation, the dual-active-bridge (DAB) dc–dc converter always features the natural self-volt-second balance performance even during the transient process. Besides, different phase-shift ratios usually result in different initial series-inductance currents. Therefore, when the phase-shift ratio is suddenly changed for dealing with the change of required transferred power, a dc offset in the series-inductance current will emerge. Especially for the high-power condition, this dc offset lasts for a long time because of the high-current value but low damping conduction resistor. Then, the magnetic saturation phenomenon may emerge in the transformer, resulting in the potential failure of the converter system. To address this issue, a simple dc-offset eliminating method is proposed for the DAB dc–dc converter. Different from most of the existing methods, the proposed one is independent from the phase-shift modulation method. Therefore, the proposed dc-offset eliminating method can be easily embedded in different phase-shift modulation methods, such as single-phase-shift, double-phase-shift, and triple-phase-shift methods. Finally, the experimental results are provided to verify the effectiveness of the proposed dc-offset eliminating method for the DAB dc–dc converter.

engineering, electrical & electronic
Adaptive Zero-IF I/Q Imbalance and DC Offset Calibration Algorithm

Jingrui Xiang,Shulin Tian,Peng Ye,Jie Meng

DOI: https://doi.org/10.1109/icemi52946.2021.9679554

2021-01-01

Abstract:The zero-IF receiver is widely used, and has the advantages of having a simplified structure, low design difficulty, and low power consumption owing to the elimination of an IF processing unit. However, limitations caused by device technology and design errors have resulted in the I/Q imbalance of the quadrature mixer circuit, which causes a sharp deterioration in the receiver's image rejection capability. Thus, the system's SNR and dynamic range are substantially affected. At the same time, due to the high power of the LO signal and the limited isolation between the mixer's RF and the LO port, the LO can be coupled to the RF link through the mixer, dielectric substrate, and space, and the DC signal can be obtained through self-mixing. The DC signal will be superimposed on the baseband signal, thereby reducing the SNR of the target signal and influencing the demodulation performance. This paper proposes an adaptive I/Q imbalance and DC offset calibration algorithm, which suppresses image frequency by removing the conjugate term, thereby automatically correcting I/Q imbalance. The DC component is also eliminated by achieving two consecutive Hilbert transforms. After testing, the proposed algorithm shows good calibration effect, simple implementation, low algorithm complexity, and high real-time performance.
Calibration of DC offsets in quadrature mixing structure based on Hilbert transform

Lianping Guo,Peng Ye,Yu Tian,Hao Zeng,Jie Meng

DOI: https://doi.org/10.1063/1.5082373

Abstract:DC offsets in a quadrature mixing structure will affect the system performance. This paper proposes a Hilbert transform-based algorithm to blindly calibrate the DC offsets by filtering the inphase and quadrature signals with the same Hilbert filters. Compared with the traditional averaging-based method, this method consumes less time and resources. Moreover, the proposed method need not interrupt analog-to-digital converter's conversion, featuring the characteristics of high efficiency and good real-time performance. The Matlab simulation results verify the correctness of the proposed algorithm, and finally, an experimental platform is designed in detail to verify the practicability of this blind calibration algorithm.
I/Q Imbalance Calibration in Wideband Direct Conversion Receivers

Zhen-Zhen Zou,Shao-Xiang Zeng,Peng Chen,Xu-Tao Yu

DOI: https://doi.org/10.1109/icuwb.2016.7790607

2016-01-01

Abstract:A wideband correction technique is proposed to calibrate the I/Q imbalance of wideband direct-conversion receivers (DCR). The wide bandwidth of input signal is divided into a series of narrow-band in which the I/Q mismatches are frequency-dependent. By using test signals in above narrow-band, the correction coefficients a and b can be calculated at corresponding frequencies. And then the coefficient curves over the whole wideband can be obtained based on cubic spline interpolation. With this method, the image rejection ratio (IRR) of DCR is generally increased 30dBc in the whole band after calibration, and the performance is improved significantly.
DC offset mismatch calibration for time-interleaved ADCs in high-speed OFDM receivers

Yulong Zheng,Zhiting Yan,Jun Ma,Guanghui He

DOI: https://doi.org/10.1007/978-3-642-35898-2_24

2013-01-01

Abstract:Zero Intermediate Frequency (zero-IF) receivers with two analog-to-digital converters (ADCs) in In-Phase and Quadrature (IQ) branches are widely used in emerging multi-Gigabit wireless Orthogonal Frequency Division Multiplexing (OFDM) systems. Because ordinary ADCs could not meet the demands of sampling rate in the system, two time-interleaved analog-to-digital converters (TI-ADCs) could be an attractive alternative for sampling speed improvement in the receiver. However, the mismatches among the parallel sub-ADCs can degrade the performance significantly without calibration. Targeting the DC offset mismatch of the TI-ADCs, this paper proposes calibration algorithm based on decorrelation least-mean-squares (LMS) and recursive-least-square (RLS) utilizing the comb-type pilots in OFDM frame, which could calibrate the two TI-ADCs in (IQ) branches simultaneously. The calibration algorithm has the property of fast convergence. Simulation results show that the BER performance is improved by the proposed algorithm. © 2013 Springer-Verlag.
A Three-stage Analog Low-Frequency Drift Calibration and DC Offset Correction Circuit for Ultrasonic AFE

Siqing Wu,Xinwei Yu,Xingtao Zhu,Fan Ye,Junyan Ren

DOI: https://doi.org/10.1109/asicon58565.2023.10396542

2023-01-01

Abstract:This paper presents a three-stage DC offset Correction circuit (DCOC) for continuous signals in the ultrasonic analog front-end (AFE). In ultrasonic systems, time-varying attenuation and high-gain operational amplifiers introduce two mechanisms that degrade signal quality: static DC offset and dynamic low frequency offset drift. The proposed DCOC utilizes a fully differential self-biased complementary common source structure, and incorporates a pseudo-resistance with adjustable resistance to achieve a G-ohm level resistance in a compact area. Moreover, it can effectively solve the problem of pseudo-resistance instability working in the sub-threshold region while detecting and providing feedback for DC offset. When the DCOC is turned on, the offset change caused by PVT fluctuation is reduced to 1 / 4, resulting in a significant suppression of the low-frequency drift in the output offset. After enabling the TGC function, the electrical test shows that the AFE output HD2=− 60dB, HD3=− 47dB at -1dBFS.
An automatic DC-Offset cancellation method and circuit for RF transceivers

Xu Ken,Cai Min,He Xiaoyong,Chen Zhijian,Zheng Weiguo

DOI: https://doi.org/10.1109/ASICON.2015.7517123

2015-01-01

Abstract:This paper presents a novel low-cost automatic DC-Offset cancellation method and circuit for DAC in RF transmitter. The automatic DC-Offset cancellation block consists of one voltage comparator, one 5-bit R-2R auxiliary DAC and a SAR digital block. The proposed DC-Offset cancellation works during power-on sequence, then stores the value of control word in registers and shuts down the comparator and SAR block to save power after the cancellation operation. Unlike other methods, the proposed method has no influence on the desired signal, and does not disturb the work of transceiver. The proposed block is fabricated in 0.13um CMOS process as one sub-block of a RF transceiver. It occupies only 100um <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">*</sub> 200um active area, and consumes only 100uA current under 1.2 V power supply. It is a low-cost solution for cancelling DC-Offset voltage both in receivers and transmitters.
A Novel Dynamic DC-offset Canceller

HY Wang,M Lin,YM Li,HY Chen

DOI: https://doi.org/10.1109/icasic.2003.1277630

2003-01-01

Abstract:A dynamic Direct Current (DC)-offset canceller in a receiver of a communication system is presented. The dynamic DC-offset voltage is sampled and then a loop architecture is used to cancel the DC-offset voltage. The simulated results show that the DC-offset voltage is no more than 5 mV after the loop architecture is operated.
Calibration Techniques for Low-Power Wireless Multiband Transceiver.

Shouyi Yin,Jianwei Cui,Leibo Liu,Shaojun Wei

DOI: https://doi.org/10.1155/2013/754206

IF: 1.938

2013-01-01

International Journal of Distributed Sensor Networks

Abstract:The low-power wireless transceiver is the basic silicon building block of wireless sensor networks and the internet of things. In this paper, two digital calibration and compensation techniques for low-power wireless multiband transceiver are presented to adjust the VCO's tuning curves in the frequency synthesizer and eliminate the DC offset voltage in the intermediate frequency (IF) pathway. The fuzzy binary search method is applied to VCO calibration, and gain-based DC offset cancellation (DCOC) is applied. Based on these proposed methods, a multiband transceiver is designed and fabricated in 0.18 μ m CMOS with 1.8 V voltage supply. Experimental results show that with 24 MHz system clock, frequency synthesizer calibration can be completed within 450 without requiring any additional calibration prescaler, achieving a calibration resolution of 1 MHz; DC offset voltage can be reduced to less than 3.5 mV for 0 to 60 dB gain, with each calibration process taking only 1.28 ms time. The proposed techniques and corresponding circuits are proved to be cost-efficient while maintaining high performance, which is suitable for multiband and multimode transceiver integration.
A Dual-Mode Analog Baseband with Digital-Assisted Dc-Offset Calibration for Wcdma/Gsm Receivers

Xie Renzhong,Jiang Chen,Li Weinan,Huang Yumei,Hong Zhiliang

DOI: https://doi.org/10.1088/1674-4926/32/12/125001

2011-01-01

Journal of Semiconductors

Abstract:A dual-mode analog baseband with digital-assisted DC-offset calibration (DCOC) for WCDMA/GSM receiver is presented. A digital-assisted DCOC is proposed to solve the DC-offset problem by removing the DC-offset component only. This method has no bandwidth sacrifice. After calibration the measured output residual offset voltage is within 5 mV at most gain settings and the IIP2 is more than 60 dBm. The baseband is designed to be reconfigurable at bandwidths of 200 kHz and 2.1 MHz. Total baseband gain can be programmed from 6 to 54 dB. The chip is manufactured with 0.13 μm CMOS technology and consumes 10 mA from a 1.5 V supply in the GSM mode including an on-chip buffer while the core area occupies 1.2 mm2.
DC Offset and Low Frequency Noise Compensation for Direct-Conversion Receiver in Pulse Compression Radar

Jingnan Pan,Wang, Zhiyu,Shuangtian Tang,Jian Wang

DOI: https://doi.org/10.1109/iwat.2011.5752322

2011-01-01

Abstract:In this paper, we replace low-pass filter (LPF) in traditional direct-conversion receiver (DCR) in pulse compression radar (PCR) by pre-defined filter (PDF) to directly filter direct-current offset and low frequency noise. We also accordingly propose an algorithm for compensating the distance range resolution degradation caused by PDF's effect on low frequency components of received linear frequency modulation (LFM) signals. Based on the theoretical understanding on how the low frequency band influences the pulse compression, a set of newly deduced equations are used to calculate the compression, and the range resolution degradation can be recovered based on the priori knowledge of the employed LFM signal and filters. This method can be used in all pulse compression radars where pre-defined continuous radar signals are employed.
The application of the offset method in improving the double signal dynamic range of a compressive receiver

Cheng Shui

2001-01-01

Abstract:After a brief description of the compressive receivers theory and mathematical model, a mathematical analysis of the output signal of a compressive receiver is presented in detail. Then the paper lays emphasis on the use of the offset method to detect the weak signal in the side lobe of the compressive receiver. Thus the limitation of the compressive receivers double signal dynamic range will be overcome effectively. Finally, the result of computer simulation is given.

Analysis of DC Offset Calibration Techniques for Direct-Conversion Receivers

An Effective DC Offset Calibration Method Combined with Analog and Digital Circuits for Direct Conversion Receivers

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A Frequency-Domain I/Q Imbalance Calibration Algorithm for Wideband Direct Conversion Receivers Using Low-Cost Compensator.

A DC Offset Cancellation Circuit Using Digital Assistance Technique and Self-Calibrating Comparator for RF Transceiver

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

Digitally Assisted IIP2 Calibration for CMOS Direct-Conversion Receivers

A LUT-free DC Offset Calibration Method for Removing the PGA-gain-correlated Offset Residue.

A Low-Power DC Offset Calibration Method Independent of IF Gain for Zero-if Receiver.

A Simple DC-Offset Eliminating Method of the Series-Inductance Current for the DAB DC–DC Converter

Adaptive Zero-IF I/Q Imbalance and DC Offset Calibration Algorithm

Calibration of DC offsets in quadrature mixing structure based on Hilbert transform

I/Q Imbalance Calibration in Wideband Direct Conversion Receivers

DC offset mismatch calibration for time-interleaved ADCs in high-speed OFDM receivers

A Three-stage Analog Low-Frequency Drift Calibration and DC Offset Correction Circuit for Ultrasonic AFE

An automatic DC-Offset cancellation method and circuit for RF transceivers

A Novel Dynamic DC-offset Canceller

Calibration Techniques for Low-Power Wireless Multiband Transceiver.

A Dual-Mode Analog Baseband with Digital-Assisted Dc-Offset Calibration for Wcdma/Gsm Receivers

DC Offset and Low Frequency Noise Compensation for Direct-Conversion Receiver in Pulse Compression Radar

The application of the offset method in improving the double signal dynamic range of a compressive receiver