Principle and application of 24-bit high-resolution analog-to-digitalconverter ADS1258

JIN Yong-jie,LONG ping,XIONG Jian-ping

2008-01-01

Abstract:In this paper,the feature,pin function and structure of ADS1258 high resolution analog-to-digital converter are introduced.The application circuit of SPI interface between C8051F120 And ADS1258 is given.The questions which in the system design needs to pay attention are explained.

What problem does this paper attempt to address?

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

Zhelu Li,Jianxiong Xi,Lenian He,Kexu Sun

DOI: https://doi.org/10.1109/APCCAS.2016.7803970

2016-01-01

Abstract:A front-end circuit with 16-channel 12-bit 100-kSps RC-hybrid successive approximation register (SAR) analog-to digital converter (ADC) for industrial monitoring application is presented. The front-end circuit can process a wide range input voltage as large as 10 V which is beyond the supply voltage, with the help of voltage divider preceding an analog multiplexer. A programmable gain amplifier (PGA) is used to convert different input voltage ranges into a same one. A RC hybrid digital-to analog converter (DAC) is employed in SAR ADC to avoid calibration requirement for the bridge capacitor which is usually needed for a split capacitor SAR ADC architecture. Serial peripheral interface (SPI) is integrated in the design for communication and configuration. The prototype circuit fabricated in a 0.18 um 3.3 V CMOS process shows the measured DNI, and IN1, within-0.821+0.68 LSB and-0.851+0.82 1,SR, respectively. The circuit consumes 2.04 mVV with a 3.3 V supply voltage. The whole chip occupies an area of 1.844 x 1.387 mm(2).
Design of a 12 bit High-Stability Digital-to-Analog Converter

Zhiyu Wang,Jinpeng Qiu,Tong Liu,Jiarui Liu,Jingjing Lü,Faxin Yu

DOI: https://doi.org/10.13290/j.cnki.bdtjs.2017.04.002

2017-01-01

Abstract:A 12 bit high-stability controlling digital-to-analog converter (DAC) was designed.By integrating a new low-offset bandgap reference (BGR) with stable start-up circuit,the DAC improved the stability of the reference circuit and the sensitivity to the temperature and process.An improved twostage resistor string structure was adopted by the DAC,which improved the accuracy of the DAC and reduced the influence of the process concentration gradient on the overall performance without increasing the circuit power consumption and expanding the chip area through the switch resistance matching and special layout.Based on the CSMC 0.5 μm 5 V 1P4M process,the designed DAC chip was verified.The test results show that the differential nonlinearity (DNL) of the DAC at room temperature is less than 0.45 LSB and the integral nonlinearity (INL) is less than 1.5 LSB.Moreover,the DNL in the temperature range of-55 ℃ to 125 ℃ is less than 1 LSB and the INL is less than 2.5 LSB.The power consumption of the 5 V supply voltage is 3.5 mW,achieving the design objectives of high precision and high stability.
Design of a Novel 8-Bit 0.35-&Amp;#x00b5;m BiCMOS Pipelined ADC

Guang Xi,Hongxia Liu,Xiaopeng Yu

DOI: https://doi.org/10.1109/edssc.2009.5394248

2009-01-01

Abstract:The pipelined ADC can keep high speed and low power consumption when it achieves high conversion accuracy, it can compromise between speed, conversion accuracy, power consumption and chip area. It is very suitable to be used in system integration and portable devices. This paper presents a novel pipelined analog-to-digital converter (ADC). Based on 0.35 μm BiCMOS process, the design is verified using the sample frequency of 250 MHz. The results show that signal to noise ratio (SNR) and Spurious Free dynamic range (SFDR) can reach 46-dB and 64.8-dB respectively. The power consumption of the key A/D circuit is 118 mW when the supply voltage is 3.3 V.
A 14-bit 500MS/s and 1GS/s Configurable Pipelined ADC with Background Calibration

Yanhua Zhang,Lijie Yang,Ruirui Dang,Zhiwei Xu,Chunyi Song

DOI: https://doi.org/10.1109/ICAM.2018.8596556

2018-01-01

Abstract:A 14-bit 500-MS/s and 1-GS/s configurable pipelined Analog-to-Digital Converter (ADC) is implemented in 28 nm CMOS. The ADC leverages dither and correlation-based background digital calibration techniques to correct the interstage gain and settling errors. A dithering technique is employed to inject a large dither signal to randomize residual non-linearity in the pipelined ADC. In order to speed up the correlation-based calibration, a variable-step-size LMS algorithm is used to extract the error coefficients. An optional interleaved mode is provided, where the two ADCs on a chip are time-interleaved to realize a single 14-bit 1 GS/s ADC. After calibration, the ADC achieves a 61.64 dB SNDR and 71.83 dB SFDR at 1 GS/s sample rate. The chip occupies 6 mm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> area and consumes 1.4 W at 2.0/1.0 V supplies.
Characteristic and Application of High Speed A/D Converter MAX12557

LUO Yong,WANG Ying,ZHOU Zi-wei

2006-01-01

Abstract:The MAX12557 is a new kind of 14-bit high-speed analog-to-digital converter(ADC)featur-ing low power,small size and high dynamic performance.The circuit has low cost and can be used easi-ly.The MAX12557 can be widely used in low-power data acquisition,I/Q receivers and portable instru-mentation etc.Its main character,internal structures and operation theory are introduced,and an exam-ple of its application in wide-band IF digital receivers is given.
Design on High Precision, Multi-channel Data Acquisition System with AD7738

DU Bing-tuan,LI Bin

DOI: https://doi.org/10.3969/j.issn.1002-8684.2007.07.015

2007-01-01

Abstract:A high-precision data acquisition system based on AD7738 is introduced in this paper. C8051F320 microcontroller and high-speed transistor optocoupler are used to develop high-precision data acquisition system and to communicate with computer by USB interface. The experimental results show that when the conversion rate is 1 kHz/s, the measured precision is up to 19 bit.
Functions and Application of A/D Converters MAX125

Xinan Zhang

2003-01-01

Abstract:The properties of function and working process of a high speed 14digit ADC MAX125 with 8 channels is introduced and how to decide the working modes is discussed. The flow chart of its software and the practically applied interface of microprocessor is presented.
Design of Data Acquisition System of Chromatograph Based on ADS1253

罗范谊,罗飞

DOI: https://doi.org/10.3969/j.issn.1008-0570.2009.20.009

2009-01-01

Abstract:In the paper,the 24-Bit Analog-to-Digital converter ADS1253,in the data acquisition system of chromatograph,converts the analog singles of voltage into digital singles,and then the digital singles are red and transmitted to PC by SCM.Details about hardware and software design of this system are introduction.Anti-jamming design is used in the hardware circuit,and program flowchart is given in the part of soft design.The result of examination indicate that the data collected is accurate and reliable in this system,which makes sure that more sample components will be detected.
Principle and Application of the Programmble Multi-Channels ADC THS1206

Hong Sun

2005-01-01

Abstract:The THS1206is a programmble,multi-channels,low-power,12-bit anglog-to-digital convertˉer(ADC)with an integrated FIFO.The characteristics,pin functions,inside structure and define of control regisˉter of THS1206are introduced.The design of multi-channels data acquisition system is presented.
Design of multi-channel data acquisition based on ADS125x and related accuracy improving method

Fei KONG,Guo-qing DING,Xin CHEN

DOI: https://doi.org/10.3969/j.issn.1674-6236.2015.08.029

2015-01-01

Abstract:ADS125x is multi-channel and high-performance 24-bit ADC which is based onΔ-Σtechnology. Theoretically, it can achieve 23-bit noiseless resolution and a maximum 30,000SPS sampling rate. The present study focused on the design of a unipolar and multi-channel data acquisition system with ADS125X based on embedded system. Additionally, it summed up several ways to improve the system's sampling precision with high sampling rate in practice. The test of effective number of bits (ENOB) in this design shows that with 1000 sampling rate, ENOB of unipolar and multi-channel data acquisition can still reach 19.6 bits, which verifies the effectiveness of the scheme.
The Principle and Application of Dual 8-bit 1Gsps ADC AT84AD001

Zhang Ning,Xu Hong-guang

2006-01-01

Abstract:AT84AD001 is a double channel,parallel and 8bits high speed ADC produced by Atmel Co.,which fastest sampling rate can reach 1Gsps and its sampling rate can reach 2Gsps in interlaced mode.It has many kinds of ways for analog input and the clock input,so it's possible to realize the electric circuit plan of multi-purpose data acquisition with the using of these characteristics.The article introduces the main parameter,the principle of working and the pins' function of this chip,and gives the connection diagram of AT84AD001,also the FPGA.
Design of seismic information acquisition module based on ADS1255

JIN Zhong,ZHANG Guo-bao

2009-01-01

Abstract:In order to satisfy the demand of high precision information acquisition in seismic information acquisition sys- tem,a new seismic information acquisition module is designed in this paper,which uses 24 -bit,Δ -Σanalog -to-digital ADS1255 as a core and TMS320F2812 as the main acquisition controller.The hardware and software design of the module are also discussed in detail.This seismic information acquisition module has a wide range of acquisition output data rate and dependable sampling precision,and is widely applied to many high precision acquisition system.
18-Bit A/D Converter AD7674 and Its Application

朱志伟,周志光,刘琼

DOI: https://doi.org/10.3969/j.issn.1674-6236.2010.04.053

2010-01-01

Abstract:In consideration of the higher and higher requirement of data acquisition precision and speed on the ultrasonic measuring distance system recently,at the same time,the simple interface circuit and high reliability was also required,a high-speed data acquisition system used in collecting ultrasonic echo signals was designed and implemented.This system takes the master-control unit with TMS320F2812,takes AD7674 as the high-speed ADC,takes the data transmission con-nection by SPI.Through the research of TMS320F2812 and the AD7674 SPI succession and controls register,it gave the method of disposing the SPI pattern correctly and the controlled process,and solved the critical path of the signal integrity problems.Actual trial shows that in 40kHz ultrasonic ranging system,the error is not more than 2mm,the blind controlled is less than 1cm,it meets the high-precision ultrasonic echo ranging system signal acquisition needs.
The Design and Application of an Altimeter System Based on 89C52

YUAN Jie,HAN Bo,LI Ping

DOI: https://doi.org/10.3969/j.issn.1001-4551.2005.10.009

2005-01-01

Abstract:This paper accounts for the design problem of an altimeter system based on 89C52,which is an 8 bit microcontroller produced by ATMEL. Specially,it depends on the relationship between pressure,temperature and altitude.The most important points in this paper is that it uses the I/O in 89C52 to achieve the function of SPI,which makes the A/D function come true with TLC2543.Thereafter it transfers the data which is processed to the LCD,also it returns the data to the control computer through RS232.
10 Bit A/D Converter TLC1549 and its Application

Wang Qi,Tan BaoCheng,Gao Tian,Yang Jie

DOI: https://doi.org/10.3969/j.issn.1671-4792.2005.12.036

2005-01-01

Abstract:This paper presents the main features of 10-bit A/D converter TLC1549 produced byTI company and introduces the chip’s application in temperature control system.
Application of ADC14C080 in High Speed Data Acquisition Circuit

Yu-yang ZHAO,Lin-fei LIU

DOI: https://doi.org/10.3969/j.issn.1673-0097.2014.03.005

2014-01-01

Abstract:This paper introduces the performance index of A/D converter ADC14C080 with 80 MPSP sampling rate and 14 bit accuracy, then the ADC front-end circuit is designed. The control and storage logic is discussed in the FPGA.
Software Implement of Resolver-to-Digital Converter Based on AD7655

HE Wen-jing,XU Xiao-wen,SHI Zhong-ke

DOI: https://doi.org/10.3969/j.issn.1000-8829.2013.04.034

2013-01-01

Abstract:A resolver-to-digital converter based on high-speed 16 bit A/D is proposed.The system design concept and software design process are presented.The driver module and signal conditioning,acquisition,calculating, storage and uploading of the 4-pole resolver are completed as well.Meanwhile,the error of the system is discussed.The results show that the system achieves simple structure,high resolution,good anti-jamming performance and flexibility.
Application and introduction of a new analog-to-digital converter serial-out

卢鑫,庞伟正

DOI: https://doi.org/10.3969/j.issn.1003-353X.2001.06.003

2001-01-01

Abstract:TLC2543 is a newfashioned ADC(analog-to-digital converter) from TI Corp..This thesis mainly describes how to construct 12-bit data acquisition system using the TLC2543 serial-out interface in conjunction with a range of three popular microcontrollers. The three microcontrollers used are TMS370,68HC 11 and 80C51. The functions and principium of TIC2543 are also briefly introduced.
Serial 12-Bit A/D Converter ADS7812 and Its Application

傅晓程,阮秉涛

DOI: https://doi.org/10.3969/j.issn.1003-0107.2002.01.010

2002-01-01

Abstract:This thesis introduces a high performance, serial data interface 12-bit A/D converter ADS7812 and its basic construct, performance and application method.
A 10-Bit 120-Ms/s Pipelined ADC with Improved Switch and Layout Scaling Strategy

Zhou Jia,Xu Lili,Li Fule,Wang Zhihua

DOI: https://doi.org/10.1088/1674-4926/36/8/085008

2015-01-01

Abstract:A 10 bit, 120 MS/s two-channel pipelined analog-to digital converter (ADC) is presented. The ADC is featured with improved switch by using the body effect to improve its conduction performance. A scaling down strategy is proposed to get more efficiency in the OTA's layout design. Implemented in a 0.18-mu m CMOS technology, the ADC's prototype occupied an area of 2.05 x 1.83 mm(2). With a sampling rate of 120-MS/s and an input of 4.9 MHz, the ADC achieves a spurious-free-dynamic range of 74.32 dB and signal-to-noise-and-distortion ratio of 55.34 dB, while consuming 220-mW/channel at 3-V supply.

Principle and application of 24-bit high-resolution analog-to-digitalconverter ADS1258

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

Design of a 12 bit High-Stability Digital-to-Analog Converter

Design of a Novel 8-Bit 0.35-&Amp;#x00b5;m BiCMOS Pipelined ADC

A 14-bit 500MS/s and 1GS/s Configurable Pipelined ADC with Background Calibration

Characteristic and Application of High Speed A/D Converter MAX12557

Design on High Precision, Multi-channel Data Acquisition System with AD7738

Functions and Application of A/D Converters MAX125

Design of Data Acquisition System of Chromatograph Based on ADS1253

Principle and Application of the Programmble Multi-Channels ADC THS1206

Design of multi-channel data acquisition based on ADS125x and related accuracy improving method

The Principle and Application of Dual 8-bit 1Gsps ADC AT84AD001

Design of seismic information acquisition module based on ADS1255

18-Bit A/D Converter AD7674 and Its Application

The Design and Application of an Altimeter System Based on 89C52

10 Bit A/D Converter TLC1549 and its Application

Application of ADC14C080 in High Speed Data Acquisition Circuit

Software Implement of Resolver-to-Digital Converter Based on AD7655

Application and introduction of a new analog-to-digital converter serial-out

Serial 12-Bit A/D Converter ADS7812 and Its Application

A 10-Bit 120-Ms/s Pipelined ADC with Improved Switch and Layout Scaling Strategy