Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Compatibilisation of Blends of Poly(vinyl Chloride) and Poly(styrene-Block-(ethylene-co-butadiene)-block–styrene) with Maleic Anhydride Grafting

Influences of compatibilizer on the morphology structure of PVC/PA6 blend systems

Synergistic compatibilization effect on phase morphology evolution and properties of poly(ether- block -amide)/ethylene-vinyl acetate blends

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Preparation and properties of PC/bPE compatibilized blends

Structure and Properties of Compatibilized Recycled Poly(ethylene Terephthalate)/linear Low Density Polyethylene Blends

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Toughening and compatibilization of polyphenylene sulfide/nylon 66 blends with SEBS and maleic anhydride grafted SEBS triblock copolymers

Effect of Compatibilizer Content on the Tensile Properties and Fracture Toughness of High Density Polyethylene/Polystyrene Blends

Influence of Compatibilizers on the Properties of PVC/PA6 Compounds

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Miscibility, Phase Behavior, and Mechanical Properties of Ternary Blends of Poly(vinyl Chloride)/polystyrene/chlorinated Polyethylene-Graft-polystyrene

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Super Tough PA6/PP/ABS/SEBS Blends Compatibilized by a Combination of Multi-Phase Compatibilizers

Compatibilizing modification of polyethersulfone/polycarbonate blend

Polystyrene/High Density Polyethylene Blends Compatibilized by a Tri-Block Copolymer I. Properties and Morphology

Synthesis of EVA-g-MAH and Its Compatibilization Effect to PA11/PVC Blends

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Preparation of HDPE/SEBS‐g‐MAH and Its Effect on Mechanical Properties of HDPE/wood Flour Composites

The Effect of Functionalized SEBS on the Properties of PP/SEBS Blends

Effects of bPE-g-MAH on Mechanical Properties and Fracture Surface Morphology of PC/bPE Blends