Abstract:Plasma electrolytic oxidation (PEO) has become an effective surface modification method to form ceramic coatings on orthorhombic Ti2AlNb alloy due to its high productivity, economic efficiency and ecological friendliness. In the present work, different contents of Al2O3 additive were introduced into a NaAlO2 basic electrolyte with the aim of improving the high-temperature properties of PEO ceramic coatings on Ti2AlNb alloy. The influence of Al2O3 addition in NaAlO2 electrolyte on microstructure, adhesive strength, isothermal oxidation behavior and tribological properties of PEO coatings at elevated temperatures was investigated by means of X-ray diffraction, scanning electron microscopy, the pull-off method, isothermal oxidation tests as well as ball-on disc friction and wear tests. The introduction of Al2O3 into the basic electrolyte promotes the formation of Al2TiO5 phase in the PEO coatings. Isothermal oxidation tests at 800 degrees C up to 150 h showed that PEO coatings with Al2O3 addition exhibit better oxidation resistance than those formed in the basic electrolyte. The PEO coating formed in the electrolyte with 4 g L-1 Al2O3 additive exhibits the least mass gain of only 1.33 mg cm(-2). The micro-hardness of the PEO coatings prepared with Al2O3 additive is improved due to the presence of Al2TiO5 phase, however, the adhesive strength of PEO coating is slightly weakened due to the formation of defects inside ceramic coating. The wear resistance of Ti2AlNb alloy is improved significantly by PEO coatings at room temperature due to high hardness and porous surface morphology. The friction coefficient and wear rate of the PEO coatings prepared with Al2O3 addition is comparable to those formed in the basic electrolyte at both room temperature and 600 degrees C.

Effects of Electromagnetic Field on Surface Roughness of High-activity TiAl Alloys

Wettability of TiAl Alloy Melt on Ceramic Moulds in Electromagnetic Field

Study of Interfacial Reaction Between TiAl Alloys and Four Ceramic Molds

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Effects of Electrical Parameters on the Microstructure of Microarc Oxidation Ceramic Coatings on Ti6al4v Alloy

Effect of Different Abrasive Particle Hardness on the Erosion Resistant Performance of α-Al<sub>2</sub>O<sub>3</sub> Ceramics

Alumina Ceramic Texturing Induced by High Magnetic Field and Its Microstructure

Effect of Different Abrasive Particle Hardness on the Erosion Resistant Performance of Α-Al<sub>2</sub>o<sub>3</sub> Ceramics

Influence of Al2O3 Addition in NaAlO2 Electrolyte on Microstructure and High-Temperature Properties of Plasma Electrolytic Oxidation Ceramic Coatings on Ti2AlNb Alloy

Effect of different abrasive particle hardness on the erosion resistant performance of α-Al2O3 ceramics

Effects of Substrate Roughness on Microstructure and Fatigue Behavior of Plasma Electrolytic Oxidation-Coated Ti-6Al-4V Alloy

Mechanical Properties and Solid Particle Erosion Behavior of LaMgAl11O19–Al2O3 Ceramic at Room and Elevated Temperatures

Effect of Aluminum by Magnetron Sputtering on the Micro-Arc Oxide Film Layer of Titanium Alloy

Effects of Electric Parameters on Structure and Thermal Control Property of Peo Ceramic Coatings on Ti Alloys

Effects of ultrasonic vibration on the microstructure and mechanical properties of high alloying TiAl

Effect of surface roughness on thermal contact resistance of aluminium alloy

Effect of Surface Roughness on the Development of Protective Al2O3 on Fe–10Al (at.%) Alloys Containing 0–10 At.% Cr

Composition and Mechanical Properties of Hard Ceramic Coating Containing Α-Al2o3 Produced by Microarc Oxidation on Ti–6Al–4V Alloy

Effects of duty ratio at low frequency on growth mechanism of micro-plasma oxidation ceramic coatings on Ti alloy

Studies of composition and properties of mullite coatings on the aluminium alloy LY12

Effect Of Talc And Titania On The Microstructure And Mechanical Properties Of Alumina Ceramics