Abstract:Directional solidification of A1-4.5Cu alloy refined by adding Al-5Ti-1B has been carried out to investigate the texture formation and grain boundary characteristic of the paramagnetic crystal under a high magnetic field. OM and EBSD were applied to analyze the microstructures solidified at different temperature gradients (G) and magnetic field intensities (B). The results show that at the temperature gradient of 27 K/cm; the orientations of fcc alpha-Al grains without magnetic field are random. However, as a high magnetic field is imposed, the easy magnetization axes < 310 > of the alpha-Al grains are aligned parallel to the direction of the magnetic field leading to < 310 > texture. Meanwhile, the ratio of coincidence site lattice (CSL) grain boundaries increases with the increment of magnetic field intensity and reaches its maximum value at 4 T, but decreases as the magnetic field enhances further. On the other hand, when the temperature gradient is elevated, columnar dendrite morphology is exhibited without magnetic field; while a 6 T high magnetic field is introduced, the columnar dendrites are broken and equiaxed grains of random orientations are obtained. The alignment behavior of the free crystals in melt could be attributed to the magnetic crystalline anisotropy of alpha-Al. Moreover, the influence of fluid flow on the texture formation and CSL grain boundary development under magnetic field is discussed. The absence of convection is benefit for grain reorientation and CSL boundary formation. The application of high static magnetic field will inhibit the macro-scale convection. However, the interaction between thermoelectric current and magnetic field will cause micro-scale fluid flow, i.e., thermoelectric magnetic convection (TEMC). The TEMC will give rise to perturbation near the solid-liquid interface leading to the appearance of freckles as well as the decreasing of the ratio of CSL boundary. Moreover, it is proposed that the formation of CSL boundary is associated with the rotation of the free grains in melt along specific crystallographic axes by magnetic torque.

Alumina Ceramic Texturing Induced by High Magnetic Field and Its Microstructure

Microstructure and Electromagnetic Properties of Fe-Si-Al Flakes Produced from Melt-Spun Ribbons

Control Of Ceramic Material Microstructure With Super High Magnetic Field

Preparation of textured porous Al2O3 ceramics by slip casting in a strong magnetic field and its mechanical properties

Effect of interfacial Fe3O4 nanoparticles on the microstructure and mechanical properties of textured alumina densified by ultrafast high-temperature sintering

Ultrafast high-temperature sintering of dense and textured alumina

Effect of heat treatment on the microwave electromagnetic properties of flaky Fe-Si-Al magnetic powders

Effect Of The Initial Time Of Polymerization On Texture Of Si3n4 Ceramics In A Strong Magnetic Field

Anisotropic Sintering Shrinkage of Spherical Alumina Particle Compact Aligned in High Magnetic Field

Anisotropic Sintering Shrinkage And Grain Growth For Spherical Alumina Powder Compacts Aligned In High Magnetic Field

Texture Formation and Grain Boundary Characteristic of A1-4.5cu Alloys Directionally Solidified under High Magnetic Field

High Density Dislocation and Magnetoplasticity in Nano-Sized Alumina Reinforced 7055Al Composites Subject to High Magnetic Field

Influence of electrical field on microstructure and mechanical properties of flash sintered alumina ceramics

Effect Of Beta-Si3n4 Initial Powder Size On Texture Development Of Porous Si3n4 Ceramics Prepared By Gel-Casting In A Magnetic Field

Effect of Sintering Conditions on Texture Formation of Si3N4 Ceramic Shaped Up in a Strong Magnetic Field

3D crystallographic alignment of alumina ceramics by application of low magnetic fields

Preparation of C-Axis Textured SiC Ceramics by a Strong Magnetic Field of 6 T Assisted Gel-Casting Process

Effect of high magnetic field assisted heat treatment on microstructure and properties of AlCoCrCuFeNi high-entropy alloy

Magnetic field treatment effects on microstructure and properties of A356 aluminium alloy

Improved Fracture Behavior and Mechanical Properties of Alumina Textured Ceramics

Discussion on magnetic-induced polarization Ampere’s force by in situ observing the special particle growth of alumina during microwave sintering