Abstract:In micro-electrical discharge machining (micro-EDM) using the non-hollow circular cross-section tool electrode with the side flushing technique, when the aspect ratio of machined micro-hole is expected to be further increased, the discharge debris expelling speed and the working fluid renewal efficiency are weakened, which hinders the improvement of machining efficiency and accuracy with increased machining depth. In order to reveal the flow behavior of the working fluid in the micro-EDM gap, so as to realize the high-precision and high-efficiency machining of micro-hole with high aspect ratio, a three-phase flow simulation model of fluid, bubble, and debris is established in Fluent under the ideal assumption that the spark discharges occur continuously to generate high-pressure bubbles. The simulation results show that when the boundary condition of the flushing pressure at the side gap entrance is set to 0, the pressure wave emitted when the high-pressure bubble expands, which is formed by the instantaneous gasification of the working fluid between electrodes under high temperature, is the source of pneumatic force that drives the working fluid flow at the micron scale. Affected by the gap flow channel structure and the viscous resistance from inner wall, the flow velocity direction of the fluid dragging the discharge debris to rise up and expel will change, forming a dynamic alternation process of flowing into and out of the side machining gap entry. As the machining depth increases, due to the energy attenuation of the pressure wave propagating from the bottom gap to the side gap entrance, the expelling speed of the discharge debris decreases exponentially at the side gap entrance, resulting in the reduced machining efficiency and accuracy. However, when the simulated bubble generation frequency is increased to the megahertz level, the expelling efficiency of debris has a step-like improvement. The continuous and high-frequency generation of high-pressure bubbles can maintain a high pressure gradient in the bottom gap, and the discharge debris is able to continuously move upward without falling back to accumulate in the bottom gap, which is beneficial to the stable and smooth machining process, realizing the high-precision and high-efficiency machining of micro-hole with high aspect ratio.

Micro EDM Deposition in Air by Single Discharge Thermo Simulation

Analysis and simulation of micro electro discharge machining process

Thermal simulation of microelectrode machining process during block electrical discharge grinding

Progress in modeling of electrical discharge machining process

A New Thermal Model for Predicted Discharge Craters in Micro/Nano-EDM Considering the Non-Fourier Effect

An Investigation into Accumulative Difference Mechanism in Time and Space for Material Removal in Micro-EDM Milling

Development of a Hybrid Intelligent Process Model for Micro-Electro Discharge Machining Using the TTM-MDS and Gaussian Process Regression

An Analysis of the Uneven Tool Electrode Wear Mechanism in the Micro-electrical Discharge Machining Process

The Principle and Realization of Micro EDM Deposition Technology

To investigate the effect of discharge energy and addition of nano-powder on processing of micro slots using EDM assisted μ-milling operation

Cutting force modeling in the electrical discharge assisted milling of Ti-6Al-4V in a multi-hybrid energy field based on finite volume method

Simulation and Experimental Study on Metal Microstructure of Meniscus‐Confined Electrodeposition

Numerical analysis of the powder mixed electrical discharge machining (PMEDM) process for TZM-molybdenum superalloy using finite element method

Micro Electrical Discharge Machining of Ultrafine Particle Type Tungsten Carbide Using Dielectrics Mixed with Various Powders

Thermal-fluid coupling model of crater formation in electrical discharge machining

Simulation Study on Gap Flow Field in EDM Micro-hole Machining Based on Gas-liquid-solid Three-phase Flow

Numerical simulation of thermal-flow-magnetic coupling dynamics during P-type monocrystalline silicon removal in electrical discharge machining

Interelectrode gas–liquid-solid three-phase flow analysis and simulation for drilling holes with high aspect ratio by micro-EDM

Experimental Investigation and Optimization of Rough EDM of High-Thermal-Conductivity Tool Steel with a Thin-Walled Electrode

Research on machining Technology of Electrospark-electrochemical Hybrid Energy Field with tungsten hole

Investigation of the Material Removal Mechanism in Electrochemical Discharge Drilling Using a High-Speed Rotating Helical Tool-Electrode