Abstract:TiAl-based alloy have potential as high temperature structural materials for aerospace applications, especially for thermal protection systems in aerospace vehicles including skin materials. Unfortunately, the ductility and formability of TiAl-based alloys are rather poor and thus gamma-TiAl sheets or foils are quite difficult to be manufactured by traditional methods and still far from practical applications. In the present work, commercial pure Ti foils and in-house fabricated TiB2/Al composite foils were alternately stacked and rolled to prepare Ti-(TiB2/Al) laminates, and then heat treatment was utilized to make liquid Al react with solid Ti, and finally TiAl-based composite sheet with multi-layer distributed reinforcement TiB2 particles were achieved. This method avoided the direct deformation of brittle TiAl billets and thus the near-net-shape processing of TiAl-based alloys sheets was feasible. Phase transformation and microstructure evolution during heat treatment were investigated and mechanical properties of the resulting micro-laminated TiB2-TiAl composite sheets were evaluated. The results showed that porous TiAl3 layers were produced by the reaction between liquid Al and solid Ti because of Kirkendall effect, and the following densification treatment under 50 MPa at 1300 degrees C for 2 h significantly improved the relative density of material. Subsequently, the reaction diffusion between TiAl3 and residual Ti proceeded in the following heat treatment, and finally fully lamellar (alpha(2)-Ti3Al+gamma-TiAl) layers were obtained. TiB2 particles did not participate in any reaction and remained, and displayed multi layered distribution in the matrix (alpha(2)-Ti3Al+gamma-TiAl) layers. TiB2 rich layer hindered the coarsening of lamellar colony of (alpha(2)-Ti3Al+gamma-TiAl) layer. Tensile properties at 800 degrees C of multi layered TiB2 TiAl composite sheets remarkably increased because of an increase of energy dissipation caused by plastic deformation.

Research on Ti-Al/Nb Multilayer Composites Fabricated by EB-PVD

Structure and Property Research on TiAl/NiCoCrAl Multilayer Composites Fabricated by EB-PVD

Fabrication, Microstructure and Properties of Electron Beam-Physical Vapor Deposited Tial Sheet and Tial/Nb Laminated Composites

Electron Beam-Physical Vapor Deposited TiAl-based Laminated Composite Sheet with Nb Layer Toughening

PREPARATION AND PROPERTIES OF TiB2/TiAl COMPOSITE SHEETS WITH LAYERED STRUCTURE

Microstructure and Mechanical Properties of Ti/Ti-Al Multi-layered Composite Prepared by EB-PVD

Microstructure of Multilayer Interface in an Al Matrix Composite Reinforced by TiNi Fiber.

Fabrication Of Multilayers Coatings Of Intermetallic Compound On Micro-Crystallization Ti-6al-4v Sheet By Al-Foil Pack Aluminizing

Microstructures and Mechanical Properties of Laminated Structural Nb-Ti-Al Composites Fabricated by Laser Deposition

Macro-microscopic Morphology and Phase Analysis of TiAl-based Alloys Sheet Fabricated by EB-PVD Method

Fracture Morphology and Residual Stresses of TiAl-Based Alloys Sheet Fabricated by EB-PVD

Optimum design, microstructure and mechanical properties of Ti/Ti 3Al multi-layered materials

Research on Sheet Metal of a New Ni-Based Superalloy Prepared by EB-PVD

Ni/Ni3Al microlaminate composite produced by EB-PVD and the mechanical properties

Microstructures and properties of in situ synthesis Ni/Ni-Al multilayer composites

Microstructure and Mechanical Properties of Ti-Al-Ti-Ti2AlNb Laminated Composites Based on the Ductile-brittle Structure

In-Situ Observation of Fracture Behavior of Ti-Aluminide Multi-Layered Composites Produced by a Hybrid Sintering Process

Investigation of Ti2AlNb-Added TiAl Composite Prepared by Direct Laser Deposition

Processing and mechanical behavior of laminated titanium–titanium tri-aluminide (Ti–Al3Ti) composites

TiAl-BASED COMPOSITE SHEET WITH MULTI-LAYER DISTRIBUTED REINFORCEMENT PREPARED BY SOLID-LIQUID REACTION

Characterization of Al/Ni multilayers and their application in diffusion bonding of TiAl to TiC cermet