Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Phase Morphologies and Dynamic Mechanical Properties of PP/PS Blends Modified by Acrylic Acid and Styrene

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Poly(L-Lactide) Materials with Balanced Mechanical Properties Prepared by Blending with Peg-Mb-Ppa Multiblock Copolymers

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Morphology, thermal behavior, rheological, and mechanical properties of polypropylene/polystyrene blends based on elongation flow

Morphology, thermal behavior, and mechanical properties of nylon6/multi-monomer grafted polypropylene blends

Effect of Styrene-Maleic Anhydride Copolymer on Properties of PBST/PLA Blends

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

The Influence of Calcium Carbonate on the Mechanical Properties and Phase Morphology of PA6/PP Blend

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Effect of Addition of Pp-G- (Gma-Co-st) on Morphologies and Properties of Pbt/Pp Blends

The effect of addition of poly(propylene-g-acrylic acid) on the morphology of poly(vinyl methylether) and isotactic polypropylene blend

FUNCTIONALIZATION OF POLYPROPYLENE AND COMPATIBILIZATION OF POLYPROPYLENE/NYLON 6 BLENDS WITH Α-Methyl STYRENE/STYRENE/MALEIC ANHYDRIDE TERNARY COPOLYMER

Influence of Epoxy Resin on the Morphological and Rheological Properties of PBT/ABS Blends Compatibilized by ASMA

Estimation of single sweep steady-state visual evoked potentials by adaptive line enhancement

Analysis of phase morphology and dynamics of immiscible PP/PA1010 blends and its partial-miscible blends during melt mixing from SEM patterns