Abstract:In this study, the morphology, surface features, textural properties, size of particles and the catalytic efficiencies of synthesized CuFe2O4 by three different methods including sol-gel (SG), coprecipitation (CP), and solvothermal (ST) were evaluated. Various analytical techniques including SEM, TEM, XRD, N-2 adsorption-desorption, EDS elemental mapping, FTIR, and XPS were employed for characteristics exploration. The characterization results showed that the synthesis method could influence the characteristics of spinal ferrite and ST-CuFe2O4 catalyst exhibited larger specific surface area (65.2 m(2)/g) and micro-pore volume (0.4512 cm(3)/g) than the catalyst prepared by CP (30.6 m(2)/g and 0.1298 cm(3)/g) and SG (18.2 m(2)/g and 0.0521 cm(3)/g) methods, respectively. Further, the XRD and FTIR results validated the formation of a highly crystalline ferrite structure synthesized by the ST method. Consequently, the catalytic results revealed that ST-CuFe2O4 catalyst exhibited excellent TCE removal (94.6%) in the persulfate (6 mM) (PS) process along with significant reusability. Moreover, scavenging test and EPR analysis validated the dominant role of symbolscript radicals for TCE removal in the PS/ST-CuFe2O4 system. Lastly, the TCE removal performance of ST-CuFe2O4 catalyst in real water matrix elucidated that PS/ST-CuFe2O4 system has promising potential and can practically be applied for remediation of TCE contaminated groundwater in ISCO practice. The ferrite synthesized by the ST method exhibited excellent catalytic performance among the three methods underlining the importance of preparation means in determining the catalytic potential of ferrite.

Studies on stability of copper-based catalysts prepared by sol-gel method

Effects of Pore Structure on Methanol Selectivity in Carbon Monoxide Hydrogenation

Stability of Copper Catalysts Prepared by Co-precipitation

Influence Factors Study of Alumina Supported Copper Ultrafine Particle by Sol-Gel Method

Facile and Flexible Preparation of Highly Active CuCe Monolithic Catalysts for VOCs Combustion

The Study of the Effects of Grain Size, Orientation and Dislocation Density on the HER Performance of Copper Catalysts

Studies on Copper Catalysts for Wet Air Oxidation of High Concentration Coking-Plant Wastewater

Studies on Flame-synthesized Low-cost Cu-based Catalysts and the Catalytic Properties

Influence of Preparation Method on Copper Ferrite Characteristics for the Efficient Degradation of Trichloroethylene in Persulfate Activated System

Study of preparation of cobalt cerium complex oxides catalyst by sol-gel method

Enhanced catalytic stability of non-stoichiometric Cu–Al spinel catalysts for dimethyl ether synthesis from syngas: Effect of coordination structure

Micro-nano structure copper-based catalyst and preparation method and application thereof

Textural Structure Effect Of Sio2 On The Catalytic Performance For Hydrogenation Of Dimethyl Oxalate To Ethylene Glycol Over Different Cu-Based Catalysts

Enhancement of Copper Catalyst Stability for Catalytic Ozonation in Water Treatment Using ALD Overcoating.

Preparation of Cu/AC Catalyst and Its Application for Desulfurization

Preparation and characterization of ultrafine particle CuO/ZrO2 catalysts I . Effect of hydrogel pH value on the morphology of the catalysts

Copper-ceria catalysts with improved water and sulfur resistance: Computational design and structural optimization

Preparation and Structural Characterization of Copper Catalysts for Water Treatment

Effect of Surfactant on Structure and Performance of Catalysts for DME Synthesis in Slurry Bed

Research on catalysts for catalytic wet air oxidation process and treatment technologies

Preparation and characterization of ultrafine particle CuO/ZrO2 catalysts II. Effect of calcination temperature on the morphology of the catalyst