Abstract:An environmentally friendly liquefaction of wood powder was prepared by atmospheric pressure liquefaction technology to replace the non-renewable petroleum polyols in the preparation of polyurethane foam composites. The liquefaction time varied from 0 min to 140 min. The composition of liquefied products and the effects of liquefaction time on the morphology, apparent density and mechanical properties of polyurethane foam composites were investigated. The results showed that the optimal process time for the preparation of wood powder liquefaction products, which could replace traditional petroleum polyols, was 110 min. At this time, polyether polyols are the main liquefaction products, with an average molecular weight in Mn reaching 237 and average molecular weight in Mw reaching 246. The functional group of the liquefied product consisted mainly of hydroxyl, with the highest content of 1042 mg KOH/g and the lowest acid number of 1.6 mg KOH/g. In addition, the surface of the polyurethane foam based on poplar wood is dominated by closed cell foam; thus its foam has good heat insulation and heat preservation properties. At 110 min liquefaction time, the apparent density of polyurethane foam is 0.164 g/cm3 and the compression strength is 850 kPa, which is higher than that of traditional polyurethane foam (768 kPa), which is without wood powder modification. Replacing petroleum polyol with renewable wood powder liquefaction products to prepare biomass-based polyurethane foam composite materials, researching complex chemical changes in different liquefaction stages, and finding the best liquefaction conditions are of great significance to optimize the performance of polyurethane, address the shortage of resources and reduce environmental pollution.

Biodegradable Polyurethane Foam with Liquefied Product from Corn Stover

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Rapid Liquefaction of Corn Stover with Microwave Heating

Optimization of Reaction Conditions for Polyurethane Foam Synthesis with Liquefied Corn Stalk by Response Surface Methodology

Processing and properties of rigid polyurethane foams based on bio-oils from microwave-assisted pyrolysis of corn stover

Liquefaction of Wheat Straw and Preparation of Rigid Polyurethane Foam from the Liquefaction Products

Lightweight Biobased Polyurethane Composites Derived from Liquefied Polyol Reinforced by Biomass Sources with High Mechanical Property and Enhanced Fire-Resistance Performance

Study on Preparation of Biodegradable Polyurethane Foam

High-Strength and Low-Cost Biobased Polyurethane Foam Composites Enhanced by Poplar Wood Powder Liquefaction

Synthesis of Bio-Based Polyurethane Foams with Liquefied Wheat Straw: Process Optimization

Characterization of Polyurethane Foams Prepared from Non‐pretreated Liquefied Corn Stover with PAPI

Microwave-assisted Liquefaction of Wood with Polyhydric Alcohols and Its Application in Preparation of Polyurethane (PU) Foams

Optimizing the preparation parameters of eco‐friendly flexible polyurethane foams derived from a corn‐based bio‐polyol

Optimization of Synthesis of Polyurethane Foam Prepared from Liquefied Corn Stover by Response Surface Methodology

Preparation and properties of novel poly(propylene oxide)-block- polylactide-based polyurethane foams

Preparation Of Rigid Polyurethane Foam From Liquefied Wheat Straw

Synthesis and Biodegradation Test of a New Polyether Polyurethane Foam Produced from PEG 400, L-Lysine Ethyl Ester Diisocyanate (L-LDI) and Bis-hydroxymethyl Furan (BHMF)

Mechanical and Thermal Properties of Polyurethane Foams from Liquefied Sugar Beet Pulp

Preparation of Biopolymer from Liquefied Corn Stover

Bio-based polyurethane foam preparation employing lignin from corn stalk enzymatic hydrolysis residues

Preparation of High Bio-Content Polyurethane Coatings from Co-Liquefaction of Cellulosic Biomass and Starch for Controlled Release Fertilizers