Abstract:Photoacid generation is a critical step in the application of chemically amplified (CA) resist technology. During the key exposure step, a catalytic amount of a strong Br4nsted acid is released within these resists. The photoacid is subsequently used in a post-exposure bake step to catalytically react with the resist polymer. In the case of a positive tone resist, an acid sensitive polymer is deprotected to render the exposed areas soluble in dilute aqueous base thereby allowing for pattern development. As the semiconductor industry begins to focus on developing 193 nm photoresists for production, it is important to identify and understand differences between prototype 193 rim CA resists and current state of the art 248 nm production worthy photoresists. The major difference between 193 and 248 nm photoresists is the exposure wavelength, which is reduced to achieve higher resolution based on the Rayleigh equation. However, this change in wavelength has several ramifications: Firstly, the tried, tested and true phenolic polymers used in DUV resists are too absorbent to be used for 193 mm application and had to be replaced by low absorbing, non-aromatic systems. Second, since even these new platforms are still more absorbing at 193 nm than the phenolic matrices are at 248 nm, the PAG loading had to be lowered significantly in order to keep the overall absorbance of the resist down. This paper describes the results of our systematic studies on understanding the reasons for observed differences in photoacid generating efficiency between 193 and 248 nm chemically amplified resist systems. First, the wavelength effect is studied by comparing the relative acid generating efficiency of onium type PAGs in a prototype 193 nm and a DUV photoresist at both 193 nm and 248 nm exposure. Second, the photoacid generating efficiency for these PAGs at 248 nm is compared in both phenolic and non-phenolic based photoresists to probe resist polymer matrix effects. Third, these experiments were repeated while varying the PAG loading in order to probe whether there is an effect of PAG loading on acid generation efficiency. Lastly, by performing all of these studies on two different onium PAG classes (iodonium and sulfonium salts), the impact of the PAG chromophore on acid generation efficiency in both sensitized and unsensitized environments was probed. In all these studies, the C-parameter method is used to determine the quantum yield of photoacid generation. First, the exposure wavelength was found to play a significant role in determining the acid generation efficiency of both PAGs, namely efficiency significantly decreases when switching exposure wavelength from 248 to 193 nm. Second, it was also found that the change in the resist matrix polymer has a profound impact on the manner in which acid is generated: The phenolic matrix enables sensitized acid generation via electron transfer from the matrix to the PAG, whereas in the acrylate polymer only direct acid generation is observed. Due to the different oxidation potential of iodonium and sulfonium PAGs, the matrix effect impacts the photoacid generation efficiency of the two PAGs very differently. This is apparent in the observed change when going from the phenolic to the methacrylate matrix. Lastly, the presence of the sensitized channel is also responsible for the observed impact of PAG loading in the phenolic polymer, which is largely absent in the acrylate matrix.

Anomalous Acid Diffusion in a Triphenylene Molecular Resist with Melamine Crosslinker

Highly Sensitive Cationic Photoresist for High-Throughput Two-Photon Nanofabrication

Chemical Amplification of a Triphenylene Molecular Electron Beam Resist

Click chemistry assisted organic-inorganic hybrid photoresist for ultra-fast two-photon lithography

Chemically Amplified Molecular Resists for E-Beam Lithography

Towards 11nm Half-Pitch Resolution for a Negative-Tone Chemically Amplified Molecular Resist Platform for Extreme-Ultraviolet Lithography

A Chemically Amplified Fullerene-Derivative Molecular Electron-Beam Resist

Performance Tradeoffs in the Design of Photoacid Generators for ArF Lithography

Performance of a high resolution chemically amplified electron beam resist at various beam energies

Chemically Amplified Phenolic Fullerene Electron Beam Resist

Positive-tone Chemically Amplified Fullerene Resist

Chemically Amplified Resist Based on Dendritic Molecular Glass for Electron Beam Lithography

Polysubstituted Derivatives of Triphenylene As High Resolution Electron Beam Resists for Nanolithography

Polymerizable Nonionic Perfluorinated Photoacid Generators for High-Resolution Lithography

Low Activation Energy Fullerene Molecular Resist

Chemically Amplified Fullerene Resists for E-Beam Lithography

10 Nm Scale Electron Beam Lithography Using a Triphenylene Derivative As a Negative/positive Tone Resist

Characterization of the Effects of Base Additives on a Fullerene Chemically Amplified Resist

CO2‐Based Dual‐Tone Resists for Electron Beam Lithography

New High Resolution Liquid Crystal Electron Beam Resists

Aqueous Developable and CO2‐Sourced Chemical Amplification Photoresist with High Performance