Abstract:Composite laminates are prone to occur delamination. Currently, there is still lacking research on the temperature effect on mode II delamination of laminates, especially the multidirectional ones. Systematically experimental and numerical studies are conducted here. Delamination tests are performed at four temperatures (-50 degrees C, 23 degrees C, 80 degrees C and 130 degrees C) on aerospace-grade T800/epoxy multidirectional laminates using an end-notched flexure set-up. Pre-cracked and non pre-cracked fracture toughness, and R-curves are measured. The non pre-cracked fracture toughness is affected by temperature. Their values at -50 degrees C, 23 degrees C and 80 degrees C are relatively close to each other while the value at 130 degrees C is 34.14% lower than that at 23 degrees C. The pre-cracked fracture toughness exhibits negligible dependence on temperature and is significantly higher than the non pre-cracked one. R-curve phenomena are observed in specimens evaluated at different temperatures, which exhibit a good linear increase with the increase in delamination length. The R-curves measured at -50 degrees C similar to 80 degrees C are similar while significantly higher than that at 130 degrees C. In addition, the bridging stress is lower when the temperature is between -50 degrees C and 23 degrees C, compared to those at high temperatures of 80 degrees C and 130 degrees C. Numerical framework for simulating the mode II delamination growth behavior is established based on the cohesive zone model. Predicted results show that the reasonable interfacial strength of cohesive elements first increases and then decreases with the increase in temperature. Temperature effect on the damage area around crack tip is also revealed.

Comparison of Mode II and III Fatigue Delamination Onset Behavior for Toughened Carbon/Epoxy Composites

Fatigue-Driven Model for Mode Ii Interlaminar Delamination Propagation of Fibre/Epoxy-Reinforced Composite Laminates under Three-Point End-Notched Flexure

Mode II Fracture Toughness Related to Ply Angle for Composite Delamination Analysis

Experimental Study on Delamination of Composite Laminates with 0°/45° Interface under Mode I, Mode II and Mixed-mode I/II Loading

Influence Of Span Ratio On The Four-Point Bend End Notched Flexure Test

Investigation of the Mode-I Delamination Behavior of Double-Double Laminate Carbon Fiber Reinforced Composite

Bridging effect on mode I fatigue delamination behavior in composite laminates

Influence of the Test Method on the Characterization of the Fatigue Delamination Behavior of a Composite Material under Mixed Mode I/II Fracture

Delamination Analysis of Carbon Fiber/Epoxy Composite Laminates under Different Loading Rates Using Acoustic Emission

Mode II delamination of a unidirectional glass fiber/epoxy composite

R-curve Behaviour of the Mixed-Mode I/II Delamination in Carbon/epoxy Laminates with Unidirectional and Multidirectional Interfaces

Mode II fatigue delamination behaviour of composite multidirectional laminates and the stress ratio effect

An Experimental and Numerical Study of the Influence of Temperature on Mode II Fracture of a T800/Epoxy Unidirectional Laminate

Mixed Mode Delamination Growth of Multidirectional Composite Laminates under Fatigue Loading

Temperature Effects on the Mode II Delamination Propagation Behavior of Aerospace-Grade CFRP Multidirectional Laminates

A comprehensive experimental investigation of the rate-dependent interlaminar delamination behaviour of CFRP composites

A semi-analytical model for the mode II fracture toughness of multidirectional composite laminates

Experimental and numerical investigation on test methods for mode II fracture of composite‐titanium adhesively bonded structures

A semi-analytical method for determining mode-II fracture toughness and bridging law of composite laminates

Interlaminar Fracture Toughness Evaluation in Glass/Epoxy Composites Using Acoustic Emission and Finite Element Methods

Loading Rate Dependency of Mode I Interlaminar Fracture Toughness for Unidirectional Composite Laminates