Abstract:LiNi0.8Mn0.1Co0.1O2||SiOx@graphite has received great attention in both academia and industry because it has the highest energy density among state-of-the-art commercial lithium-ion batteries. However, it suffers from severe capacity decay during high-temperature cycling or storage, which still needs to be addressed for its commercialization. In this work, fluoroethylene carbonate (FEC) is employed as an additive or a cosolvent to improve the high-temperature performance of 1 Ah LiNi0.8Mn0.1Co0.1O2||SiOx@graphite pouch cells. By adding 5% FEC as additive, the capacity retention increases from 54.5% to 67.0% after 100 cycles at 45 °C. The use of FEC as a cosolvent further increases the capacity retention to 83.3%. The improvement is ascribed to the multifunctional effects from FEC, preventing electrolyte decomposition, mitigating the resistance increment and Mn ions dissolution with the formation of the interface films, which consist of LiF and LiPOxFy species. Therefore, the employment of FEC is of great importance for the development of high-energy-density lithium-ion batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01679?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01679</a>.(Figure S1) Cycling performance of the NMC811||SiOx@Gr pouch cells with different electrolyte systems at 0.3 C and room temperature for 100 cycles; (Figure S2) EIS of the NMC811||SiOx@Gr pouch cells after formation and 100 cycles at 0.3 C and 45 °C; (Figure S3) SEM images of the NMC811 cathodes at raw state and after 100 cycles with the blank, 5% FEC system, and 30% FEC system; (Figure S4) TEM results of the SiOx@Gr anodes after 100 cycles for the three systems and at raw state; (Figure S5) GC-MS chromatograms of the three electrolytes after formation and 100 cycles at 45 °C; (Table S1) charge/discharge capacities and Coulombic efficiency in the first formation cycle of the NMC811||SiOx@Gr pouch cells using the three electrolyte systems; (Table S2) charge/discharge specific capacities of the NMC811 electrodes using different electrolyte systems in the voltage range of 3.0–4.2 V at 0.3 C and 45 °C; (Table S3) charge/discharge specific capacities of the SiOx@Gr anodes using different electrolyte in the voltage range of 0.005–4.2 V at 0.3 C and 45 °C; (Table S4) The main electrolyte components detected from GC-MS for the three electrolyte systems after formation and 100 cycles; (Table S5) LC-QTOF-MS results collected from the electrolytes after 100 cycles; (Table S6) LC-QTOF-MS results collected from the NMC811 cathodes after 100 cycles; (Table S7) LC-QTOF-MS results collected from the SiOx@Gr anodes after 100 cycles (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01679/suppl_file/ae0c01679_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Beneficial Effects of Oxide-Based Additives on Li-and Mn-Rich Cathode Active Materials

Improving the Cycling Performance of High-Voltage NMC111 || Graphite Lithium Ion Cells by an Effective Urea-Based Electrolyte Additive

Electrochemical performance and thermal stability analysis of LiNixCoyMnzO2 cathode based on a composite safety electrolyte

Electrolyte Optimization to Improve the High-Voltage Operation of Single-Crystal LiNi0.83Co0.11Mn0.06O2 in Lithium-Ion Batteries

Improved Electrochemical Behavior and Thermal Stability of Li and Mn-Rich Cathode Materials Modified by Lithium Sulfate Surface Treatment

Stabilizing LiNi0.8Co0.1Mn0.1O2 cathode by combined moisture and HF digestion/adsorption for high-performance lithium metal batteries

Multifunctional Fluoroethylene Carbonate for Improving High-Temperature Performance of LiNi 0.8 Mn 0.1 Co 0.1 O 2 ||SiO x @Graphite Lithium-Ion Batteries

Tuning the Interface Stability of Nickel-Rich NCM Cathode Against Aggressive Structural Collapse via the Synergistic Effect of Additives

Acid- and Gas-Scavenging Electrolyte Additive Improving the Electrochemical Reversibility of Ni-Rich Cathodes in Li-Ion Batteries

Modifying the Cathode–Electrolyte Interphase by Sulfone-Based Additive to Enhance the Electrochemical Performance of LiNi 0.5 Mn 1.5 O 4

Enhanced Electrochemical Performance of Ni‐Rich Layered Cathode Materials by Using LiPF6 As a Cathode Additive

Multifunctional Self-Reconstructive Cathode/Electrolyte Interphase Layer for Cobalt-Free Li-rich Layered Oxide Cathode

Development of Electrolyte Additives to Enable High-Voltage LiNi0.5Mn1.5O4 Lithium Ion Batteries

A Ternary Additive Mixture for Suppressed Electrolyte Decomposition and Mitigated Gassing in 5V Lnmo‖Graphite Li-Ion Cells

Surface Modification Engineering Enabling LiMn x Fe1‐ x PO4 Cathode Against Aggressive Cathode Chemistries for Excellent Performance Lithium‐ion batteries

Surface Miscible Structure Modulation of Li‐Rich Cathodes by Dual Gas Surface Treatment for Super High‐Temperature Electrochemical Performance

Opportunities and Challenges of Li2C4O4 as Pre‐Lithiation Additive for the Positive Electrode in NMC622||Silicon/Graphite Lithium Ion Cells

An Interfacial Mechanism of Chelate-Borate Electrolyte Additives in Ni-Rich LiNi 0.8 Mn 0.1 Co 0.1 O 2 Cathodes

A Novel Strategy to Suppress Capacity and Voltage Fading of Li‐ and Mn‐Rich Layered Oxide Cathode Material for Lithium‐Ion Batteries

In Situ Constructing Ultrastable Mechanical Integrity of Single‐Crystalline LiNi0.9Co0.05Mn0.05O2 Cathode by Interior and Exterior Decoration Strategy

Enabling Aqueous Processing of Ni-Rich Layered Oxide Cathode Materials by Using Lithium Sulphate as Processing Additive