Abstract:The current state of industrial production of wear-resistant cast parts from high-manganese steels using various alloying, micro-alloying and modification technologies is analyzed in order to increase wear resistance not only in conditions of shock-abrasive, but also in conditions of purely abrasive wear. It is shown that despite the large number of technologies for the production of wear-resistant parts from these steels, there are no simple and highly effective methods. Prospective directions are dispersion hardening of metal by modification and microalloying of steels, in particular with nitrogen and vanadium, dispersion hardening by alloying of steels with titanium, niobium, etc. and the use of optimal modes of heat treatment. For the conditions of intensive shock-abrasive wear, it is important to establish the regularities of the influence of the degree of shock deformation on the formation of the surface martensitic layer in products after microalloying and modification of steels with nitrogen, dispersion and dispersion nitride hardening of the metal. It has been shown that dispersion nitride strengthening of metal by modifying steel with nitrogen or joint addition of nitrogen and vanadium to it and dispersion strengthening of metal after simultaneous addition of nitrogen, titanium and niobium significantly disperse the austenite grain of steel both in the cast state and after quenching. The change in the structure of steels due to the strengthening of the metal significantly affects their mechanical properties after various modes of heat treatment. Dispersive vanadium nitride strengthening increases strength by 15...17 % and plasticity by 45...50 %, and dispersed nitride strengthening increases plasticity by 45...60 % while maintaining the level of strength and slightly reducing impact toughness. The influence of the degree of impact deformation on the formation of e and a-martensite is shown, and a clear relationship between the increase in the degree of impact deformation and the increase in the amount of a-phase in the deformed layer is established. Impact deformation of about 16.6 % increases the amount of a-martensite in the deformed layer from 40 % to 98 %, which ensures an increase in the hardness of the deformed layer from 24 HRC to 36 HRC. It was noted that nitrogen modification, dispersion nitride and impact hardening of high-manganese steels increase their wear resistance by 1.5...2.0 times under conditions of dry sliding friction and 1.7...2.0 times under conditions of abrasive wear using unfixed and fixed abrasive.

Estimation of the Efficiency of Applying Nitrogen Powder Materials in Magnetic Abrasive Processing Technology

Achieving in-situ Fe-based spherical particles for magnetic abrasive finishing process of Zirconium tube via gas nitriding method

Preparation of Al2O3 magnetic abrasives by combining plasma molten metal powder with sprayed abrasive powder

Effect of laser-assisted surface modification of NdFeB permanent magnets applicable in high-demand working environment

Recent Research Trend in Powder Process Technology for High-Performance Rare-Earth Permanent Magnets

Optimizing processing performance of Fe-6.5 wt%Si–SiC magnetic abrasive particles by in-situ formation of Fe x Si y interlayer

Parametric Studies on Finishing of AZ31B Magnesium Alloy with Al2O3 Magnetic Abrasives Prepared by Combining Plasma Molten Metal Powder with Sprayed Abrasive Powder

Enhanced Tribological Properties of CrN Coatings on Densified Surfaces of Fe-Based Porous Materials Obtained Through Powder Metallurgy and Ultrasonic Shot Peening Treatment

Hybrid post-processing effects of electropolishing-assisted magnetic abrasive finishing using CNTs-Co abrasive on stainless steel 316 surface

Influence of Process Parameters and Initial Surface on Magnetic Abrasive Finishing of Flat Surfaces on CNC Machine Tools

Eccentric magnetic abrasive finishing of 316 steel

The mechanism of increasing the wear resistance of steel 110G13L by modification, dispersion and dispersion nitride hardening

Process optimization and finite element modeling in magnetorheological abrasive finishing of SS-316L with surface characterization

New method for position and energy controlled surface mechanical attrition treatment and its effects in 304 stainless steel

Blending Powder Process for Recycling Sintered Nd-Fe-B Magnets

Optimizing the powder mixed EDM process of nickel based super alloy

Diffusion Nitride Coatings for Heat-Resistant Steels

Development of Al2O3-SiO2 based magnetic abrasive by sintering method and its performance on Ti-6Al-4V during magnetic abrasive finishing

Researches on the EDM of magnetized sintered NdFeB permanent magnetic material

Co-optimization of magnetic abrasive finishing behaviors of zirconium tube surfaces with Fe-6.5 wt% Si/SiC abrasives using BP neural network and response surface methodology

Nanoengineering steel's durability: creating gradient nanostructured spheroidal carbides and lath-shaped nano-martensite via ultrasonic shot peening