Abstract:Synthesis of nanocomposites is challenging due to the difficulties in achieving homogeneous distribution of reinforcing particles in metal. In this paper, an in‐situ Al‐MgAl2O4 nanocomposite billet was prepared by the reaction of ɣ‐Al2O3 with molten Al and ultrasonication‐assisted impeller mixing. The microstructure of the composite showed homogeneously distributed MgAl2O4 crystals alongside their clusters in the Al matrix. Microstructural analysis revealed MgAl2O4 crystals distributed from 20 nm to 4 μm in size. The hardness was found to vary within the composite from 50 Hv for the matrix to 140 Hv for particle cluster regions. The grain size was reduced from 1000 μm in reference metal (CP Al) to 100 μm in the composite. The compression strength of the composite was increased substantially and higher strain hardening effect in comparison with Al was noticed in the compression test. The signatures of extensive plastic deformation such as dislocation pileups, deformed grains, grain boundary pinning etc. were observed in the composite via transmission electron microscopy. Damping properties of as‐cast composite were higher than those of CP Al in the temperature range from room temperature to 350 °C. After rolling the composite up to 40% reduction, the damping capacity (Tanδ) of the composite was found to increase marginally after 150 °C. Higher damping was found to reoccur after the annealing treatment of the composite. The improvement in damping capacity at RT was possibly influenced by the micron sized MgAl2O4 and at higher temperatures by the nano‐sized MgAl2O4 crystals. The reoccurrence of higher damping in the annealed composite underlined the stability of finer grains due to the grain boundary pinning by nano‐sized MgAl2O4 crystals. The studies on the damping property of the composite displayed the benefits of having dual size distribution of MgAl2O4 crystals (nm and μm) in the composite. This article is protected by copyright. All rights reserved.

Influence of In-house Synthesized Micro-Aegle Marmelos Polymer Concentration on Physico-Mechanical Properties of Aluminum-Based Composites

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

A Polymer-Based Metallurgical Route to Produce Aluminum Metal-Matrix Composite with High Strength and Ductility

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Investigation On Tensile Properties Of Aluminum 7075 - Silica Particles -Boron Fiber- Reinforced Hybrid Metal Matrix Composites

Synergistic effect of hybrid reinforcement on magnesium-based composites for enriching mechanical and tribological characteristics

Fabrication, interfacial and flexural properties of a polymer composite reinforced by γ-Al2O3/Al fibres

Hybrid Filler Actions on Functional Performance Evaluation of Magnesium Alloy (AZ61) Hybrid Nanocomposites

In-situ preparation of novel composites of PMMA and Aluminum Carbide (Al4C3), investigation of thermal behavior and mechanical strength

Preparation and properties of metal-containing polyamide hybrid composites via reactive microencapsulation

Optimization of process variables and characterization of mechanically agitated ceramic‐microsphere reinforced aluminium composite

Enhanced mechanical and tribological properties of ultrasonically assisted stir-cast AA7075 metal matrix composites in challenging corrosive environments

The effect of reinforcements on mechanical properties of A7005 hybrid MMCs

Enhancing the Microstructure and Mechanical Properties of Cast Aluminum Matrix Composites Through Nano-Al2O3 Reinforcement via CMT and PMC Welding

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)

The effect of reinforcement particles weight percentage on the mechanical properties and plastic flow behaviour of aluminum alloy 7075 matrix material

Microstructural evolution and property evaluation of in‐situ Al‐MgAl2O4 nanocomposite prepared by ɣ‐Al2O3 and ultrasonication‐assisted impeller mixing

Investigation on Mechanical Properties of Agro and Industrial Waste Reinforcement in Aluminium 7075 Composite with Liquid Metal Stir Casting Route

Performance analysis and mechanical behavior of aluminum metal matrix composite